Parts for Kenmore 790.45302410 (79045302410, 790 45302410): Control Panel Parts

This replacement control knob lets you easily turn stove or oven burners and temperature controls for accurate selection and reliable operation. It restores lost grip and clear pointer alignment for safe, consistent use. What it does:

• Fits over a control shaft to select burner or oven settings
• Restores tactile grip and visible pointer for precise setting changes
• Commonly replaces cracked, stripped, or worn knobs that slip or spin
• Helps prevent accidental setting changes by providing a secure fit

• Pull old knob straight off; push replacement onto the control shaft until seated
• Verify correct orientation and pointer alignment before use
• Disconnect power/gas or follow appliance safety guidance if working near energized components

This replacement control knob restores a damaged or missing stove/range control interface so you can set burner or oven controls with a secure, easy-to-grip dial. Fits common Frigidaire-style control shafts. What it does:

• Replaces a worn, cracked, or missing control knob so settings stay accurate and secure
• Provides a clear tactile grip for turning burners or oven controls
• Prevents slip or intermittent contact from damaged knobs that can impede temperature or burner selection
• Restores normal user control of the appliance without altering functions

• Remove power to the appliance before servicing; for gas or electric ranges, ensure burners are cool
• Pull the old knob straight off the control shaft; align the replacement on the flat or D-shaped shaft and push fully into place
• Do not force if resistance is felt — verify shaft orientation and that the knob is the correct part
• If the control shaft or switch is damaged, replace the underlying component rather than relying on a knob-only repair

A small sleeve used to support and align a shaft, pin, or lever inside the appliance. Replacing a worn bushing restores smooth, quiet movement and helps prevent accelerated wear on adjoining parts for reliable operation. What it does:

• Supports and centers a rotating or sliding shaft/pin
• Reduces friction and metal-to-metal wear to minimize noise
• Helps maintain proper alignment for consistent performance
• Common signs of wear: wobbling play, squeaks/grinding, binding, or visible cracks

• One bushing

• Disconnect power and shut off gas/water before servicing
• Note the original orientation; seat the new bushing fully and squarely
• Clean mating surfaces; inspect shafts/pins for wear and replace if damaged
• Apply manufacturer-approved lubricant only if specified by your service manual

The Surface Element Switch is an OEM part for Frigidaire electric cooktops and ranges. It is an electronic component that controls the power supply to individual cooking elements on the surface.

Causes can be normal wear and tear over time, exposure to moisture, food spills or other contaminants on the cooktop. Physical damage from impacts could also cause switch failure.

Symptoms of a bad surface element switch include:

• Elements failing to heat up or staying hot even when controls are set to off
• Inconsistent or intermittent power to surface elements
• Loose, cracked, or non-responsive switches

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This switch bushing fits the control shaft to stabilize and guide rotary switches, helping restore proper knob alignment and smooth operation. It prevents wobble and uneven contact that can cause intermittent control behavior. What it does:

• Centers and supports the control shaft to keep the switch and knob aligned
• Reduces wobble and lateral play that can make knobs feel loose or inconsistent
• Helps maintain reliable electrical contact by keeping the switch properly seated
• Commonly replaced when knobs are loose, the switch wobbles, or control engagement is uneven

• One switch bushing

• Disconnect power to the appliance before starting any repair
• Requires removing the control panel or knob to access the switch shaft; small hand tools typically needed
• Inspect the switch and knob for wear while replacing the bushing; replace worn components as needed

This stainless steel cleaner restores and protects stainless surfaces, removing fingerprints, smudges and light soils to improve appearance and make routine cleaning easier. Safe for finished stainless when used as directed. What it does:

• Cleans away fingerprints, grease, and light residue from stainless surfaces
• Restores a streak-free shine and improves overall appearance
• Helps reduce visible smudges for easier routine maintenance
• Leaves a light protective finish that helps resist fingerprints between applications

• Read and follow the product label before use; test on an inconspicuous area first
• Apply to a soft cloth and wipe with the grain of the stainless; avoid abrasive pads
• Do not use on hot surfaces, painted finishes, or unsealed metals unless manufacturer approves
• Keep out of reach of children and avoid contact with eyes; if contact occurs, rinse thoroughly