Parts for Kenmore 790.47919602 (79047919602, 790 47919602): Control Panel Parts

This replacement control panel trim cover restores the appearance and protection of the appliance's front console. It keeps the control area shielded from spills and debris for a cleaner, more finished look. What it does:

• Replaces a cracked, faded, or broken control panel trim cover
• Helps protect buttons, switches, and electronics from spills and dust
• Restores a uniform, factory-finish appearance to the console
• Reduces risk of dirt buildup that can interfere with controls

• Designed to install with basic hand tools; follow OEM instructions for removal and reassembly
• Power off and unplug the appliance before beginning work to avoid shock or injury
• Handle carefully to avoid scratching the finish; align tabs and fasteners before securing

This mounting support bracket secures internal appliance components and panels, restoring proper alignment and stable operation. It's a direct-fit replacement designed to match the original bracket form and mounting points. What it does:

• Provides rigid support for panels, assemblies, or components to prevent sagging or separation
• Restores correct alignment of doors, panels, or internal parts that have shifted
• Stops rattling, vibration, or movement caused by a missing or damaged bracket
• Re-establishes mounting points needed for proper operation of adjacent parts

• Typical installation requires basic hand tools; follow OEM instructions for access and fastener torque
• Turn off power to the appliance and disconnect from its power source before starting work
• Inspect nearby fasteners and mounting holes; replace any stripped screws or damaged hardware

This replacement access panel cover protects internal components and keeps the appliance's appearance clean. It restores a sealed, finished surface after repair or part removal. What it does:

• Covers and shields internal controls or wiring from dust and debris
• Helps maintain appliance aesthetics by replacing cracked or missing panels
• Prevents accidental contact with service areas during normal use
• Common symptom: broken, cracked, warped, or missing cover exposing interior components

• One replacement access panel cover

• Disconnect power to the appliance before removing or installing the cover
• Use basic hand tools; avoid overtightening fasteners which can crack the cover
• If mounting hardware is missing or damaged, replace fasteners with OEM-equivalent parts

This control board is intended for use with ranges, ovens, and stoves. It's located on the top back area of the appliance, where users can press buttons and view temperature or time information. It's composed of a circuit board with a small display on top. The control board is used to ensure the appliance operates correctly. It controls the time and temperature of the oven and displays information for the user.If the control board is not working correctly, it may no longer show information on the display. It can also cause the oven to stop working, run at the wrong temperature, or otherwise create issues with heating. Before replacing the control board, unplug the oven from the wall. Work gloves are useful to protect the hands during the replacement process. Remove the mounting brackets on the side of the door to access the control board. Pull it out and note where wires and components are located. Remove the part and install the wires and components to the new board before installing it.This control board is typically used on ranges, stoves, and ovens made by Kenmore. It's sold as a single genuine OEM replacement part that is directly sourced from the manufacturer.

This wiring label is a self-adhesive diagram that identifies wire colors, terminal connections and circuit routing to help technicians and owners correctly reference electrical wiring during diagnosis or repair. It protects against miswiring and simplifies troubleshooting. What it does:

• Shows wire color codes, connector locations and hookup paths for the appliance's electrical components
• Helps prevent incorrect connections during service and reduces diagnostic time
• Makes it easier to confirm proper wiring after component replacement
• Useful when original markings have worn, been removed, or become hard to read

• Disconnect power to the appliance before inspecting or replacing the label
• Clean and dry the application surface; press label firmly to ensure full adhesion
• Place where it is visible and protected from heat, moisture, and abrasion

This repair parts list is the manufacturer's service sheet that identifies appliance components and part numbers to help locate and order correct replacement parts. It's a reference used during diagnosis and parts ordering. What it does:

• Lists component names, part numbers, and diagram references for accurate part identification
• Helps technicians and owners the exact replacement needed before ordering
• Reduces mis-orders by matching symptoms to listed components and assemblies
• Serves as a quick reference during repairs and parts lookup

• No installation required; use as a reference during parts selection and repair
• Keep the sheet with service records for future troubleshooting
• When replacing parts, always disconnect power and follow OEM safety instructions

Wire harness for electric wall ovens. Connects electrical components within the oven cavity. Replace if wires are frayed, damaged, or connectors are broken.

Replacement instruction sheet for your wall oven. Includes operating guidelines and care information. Ideal if your original manual is lost or damaged.

Replacement #8 x 0.500 inch screw for securing panels, trim, and brackets in appliances. Needed when original fasteners are stripped, lost, or missing.

This is a replacement screw used to secure appliance panels and components. It restores proper fastening so panels, trim, or assemblies stay tight and reduce vibration or rattling. What it does

• Fastens panels, brackets, or trim to the appliance chassis
• Helps stop loose or vibrating panels and trim pieces
• Restores proper alignment where a missing or stripped screw causes gaps or movement
• Use when the original screw is missing, damaged, or corroded

• One replacement screw as shown

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep removed screws in a safe place; this screw matches the original before installation