Parts for Kenmore 796.41483410 (79641483410, 796 41483410): Control Panel Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Installation instruction sheet for your washer. Provides setup guidance and installation steps. Replace if missing, damaged, or illegible from previous use.

Rear cover panel for washers. Protects internal components at the back of the machine. Replace if cracked, damaged, or missing to restore appearance.

Washer suspension bush that cushions and stabilizes the drum assembly. Replace if cracked, worn, or causing excessive movement during spin cycles.

Secures the drum during washer transport or relocation. Replace missing, stripped, or damaged shipping bolts to prevent internal movement and damage while moving.

Secures the washer’s tub and basket during moving to prevent internal damage. If the originals are missing after a move, install replacements for transport and remove them before using the washer.

What it does

• Locks the tub and basket to limit movement in transit
• Helps prevent suspension damage and internal rattles while relocating
• Replaces missing, bent, or stripped transport bolts
• Useful for moves, storage, or service shipments

What’s included
One shipping bolt assembly (sold individually).

Install notes

• Unplug power and turn off water before service
• Insert through the rear panel into the designated mounting point; tighten snugly—don’t overtighten
• Do not operate the washer with shipping bolts installed; remove all bolts after placement
• Some models use multiple bolts and lengths—match count/positions to your owner’s manual

Usage tip
After removal, bag and tape the bolts to the cabinet so they’re on hand for the next move.

Top plate assembly for washer control panel area. Replaces cracked, broken, or damaged top plates. Structural component that secures and supports control.

Washer lid hinge assembly connects the lid to the cabinet. Replace if your hinge is cracked, broken, or worn causing the lid to sag or not stay open properly.

A replacement holder assembly that secures and supports internal components for proper alignment and operation. Restores stable mounting where the original bracket is cracked, bent, or broken so the appliance runs quietly and reliably. What it does

• Provides a secure mounting point for internal parts that rely on a fixed support
• Prevents rubbing, misalignment, and excess vibration caused by a damaged holder
• Helps restore correct component positioning to improve part interaction and operation
• Commonly used when the original bracket is cracked, worn, or no longer holds parts firmly

• One holder assembly

• Disconnect power before starting any repair; shut off water supply if the repair requires opening plumbing
• Basic hand tools typically required; handle clips and tabs gently to avoid damage
• Inspect adjacent components for wear and replace if needed for a long-lasting repair

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Washer door won't close or latch securely? This door strike ensures proper door closure for safe operation. Easy DIY fix for common latch issues.

Cabinet base assembly for washers. Forms the bottom structural support of the cabinet frame. Replace if cracked, rusted, or damaged from moisture exposure.

Replace a broken, rusted, or missing leveling leg assembly. Installs at the base to stabilize your washer, reduce vibration, and adjust height.

Trim cap that covers exposed screws or mounting holes on your washer. Replace when cracked, broken, or missing to restore finished appearance.

Fix washer overfilling or won't fill issues with this water level pressure switch. Senses tub water level to control fill cycles. Easy DIY repair.

Washer won't start or shows dE/door lock error? This door switch detects if the door is closed so the cycle can begin. Easy DIY repair with video guide.

Protective access cover shields internal washer components from dirt and moisture. Replace if cracked, broken, or missing to restore factory protection.

This noise filter assembly is an electronic component that suppresses electromagnetic interference (EMI) generated by the washing machine's motor and control circuits. It helps prevent electrical noise from feeding back into your household wiring. Replace this part if your washer fails to start, shuts off unexpectedly, or causes interference with nearby electronics.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.