Parts for Whirlpool WFE715H0EE0: 03 - Control Panel Parts

Color: White  Note: Left side endcap

Black left side end cap panel for electric and gas ranges. Replaces cracked, broken, or damaged side trim pieces. Installs on left exterior edge.

Right side end cap panel for ranges in black. Replaces cracked, broken, or missing end panel. Covers and protects the exterior side of your range.

White plastic end cap that covers the right side panel edge of your range. Replaces cracked, broken, or missing endcaps to restore a finished appearance.

White control panel for electric and gas ranges. Replaces cracked, chipped, or damaged panels on the top front of your range. Secures with screws.

Black control panel for electric and gas ranges. Replaces cracked, broken, or worn panels on the front of your range. Direct fit installation.

Stainless steel control panel trim for electric and gas ranges. Replaces scratched, dented, or cracked panels. Installs on front with screws.

Burner won't heat or stuck on one temperature? This infinite switch controls your range surface element heat levels. DIY repair restores precise cooking.

Burner stuck on high or won't adjust temperature? This infinite switch controls heat levels for surface elements. Common DIY fix, 15-30 minutes.

If your burner won't heat, stays on high, or only works on low, replace the infinite switch. Simple 20-minute DIY repair with just a screwdriver.

Replace your range's surface unit indicator light when it stays on, flickers, or burns out. Signals when burners are hot for safety. Verify fit.

Broken indicator light lens? This red lens covers the control panel light opening, restoring visibility and protection. Easy DIY fix in under an hour.

Control knob attaches to the switch shaft on your range, letting you adjust settings. Replace if cracked, stripped, broken, or missing to restore grip.

Heat shield for electric ranges. Protects components from heat damage. Replace if cracked, warped, or missing to restore proper heat protection.

This machine screw is used across appliances to secure brackets, covers, and internal components. Replacing a missing or stripped fastener helps keep parts aligned and tight, reducing vibration and preventing loose or shifting assemblies.

• Provides machine-thread fastening for panels, brackets, and internal parts
• Helps eliminate rattling, vibration, and loose fits
• Restores proper attachment when the original screw is stripped, missing, or corroded
• Used wherever an 8-32 screw is specified in the service manual or parts list

• Disconnect power to the appliance; turn off gas/water if applicable
• Match the screw to the original location to confirm size and thread
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten to prevent stripping or cracking

Protective cover that conceals your range's control box and wiring. Replaces cracked, broken, or missing covers to restore a finished look.

Secures the control console assembly to your range, keeping the control board and interface stable. Replace if bracket is cracked, broken, or missing.

This electronic control board manages the oven and range functions, including temperature regulation, bake and broil cycles, and timer operations. It receives input from the touchpad or control panel and sends signals to the heating elements and other components. Replace this board if the oven does not heat, displays error codes, has unresponsive controls, or fails to maintain the correct temperature.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal