Parts for Electrolux ECFG3668ASA: Control Panel / Top Burners|Cecfg3668asa.Tif Parts

This spring restores proper tension to the refrigerator door hinge so the door opens and closes smoothly and stays aligned. It replaces a worn or broken hinge spring to reduce sagging and uneven door movement. What it does

• Provides hinge tension so doors close fully and seal properly
• Helps prevent door sag, misalignment, and uneven gaps
• Reduces grinding or rubbing noises from the hinge area
• Restores expected door operation after a broken or stretched spring

• One replacement hinge spring

• Disconnect power to the appliance before beginning any repair
• Use proper hand tools and keep fingers clear of the spring path; springs can release force suddenly
• Installation may require removing the door or hinge assembly; keep track of fasteners and alignment

This rotary selector switch controls cycle selection on compatible Frigidaire appliances, restoring reliable cycle changes and control-panel responsiveness. It replaces a worn or damaged selector to help regain normal user input and cycle selection. What it does:

• Changes the control's selected cycle or setting when the dial is turned
• Re-establishes mechanical/electrical contact if the original switch is worn or intermittent
• Resolves symptoms like unresponsive or stuck cycle selection, erratic setting changes, or no-change when turning the dial
• Works as the user-interface input component between the control panel and main control board

• One selector switch (rotary)

• Disconnect power (unplug or shut off breaker) before starting any repair
• Remove control panel or console to access the switch; retain all screws and fasteners for reassembly
• Note wire locations or take a photo before disconnecting terminals to ensure correct reconnection

This mounting bracket secures panels or components in place to restore proper alignment and reduce movement. Use it when an appliance panel, trim, or internal piece is loose or rattling. What it does:

• Provides a stable attachment point for a panel, trim, or internal component
• Prevents vibration and rattling caused by a failed or bent bracket
• Restores proper alignment to doors or access panels that sit unevenly
• Replaces damaged or broken mounting hardware to improve fit and finish

• Disconnect power and/or gas supply before starting work
• Access may require removing an outer panel or trim; keep fasteners organized
• Use basic hand tools; avoid overtightening to prevent stripping or damage

This regulator controls gas pressure to the range/oven's burner system so burners and oven heat reliably. It restores correct fuel flow for consistent flames and cooking performance when the regulator is failing. What it does

• Regulates incoming gas pressure for stable burner and oven flames
• Helps ensure even oven temperatures and consistent burner heat
• Common symptom: burners or oven ignite weakly or fail to maintain flame
• Common symptom: inconsistent cooking or uneven baking

• One regulator

• Turn off gas supply and disconnect power before servicing
• Inspect gas connections and leak-test after installation per local codes
• Do not modify the part; use the exact replacement for safety and proper operation

This electronic control is the refrigerator's main control board that manages temperature, defrost, and system cycles so the appliance runs correctly and maintains safe food temperatures. Replaces a failed or unresponsive control module. What it does:

• Regulates compressor, fans, and defrost timing to maintain set temperatures
• Provides command and feedback for the front display and user controls
• Can prevent normal cooling when the board is faulty, unresponsive, or shows error codes
• Helps stop erratic cycling or continuous run conditions caused by control failure

• Always disconnect power to the appliance before starting service
• Handle the board carefully and avoid static discharge; use ESD protection if available
• Follow the appliance service manual for connector locations
• After installation, restore power and confirm normal operation and temperature control

This holder is a small mounting bracket designed to secure a fridge component in place and restore proper alignment. It keeps parts stable to reduce noise and prevent wear from vibration. What it does:

• Secures the targeted component to the cabinet or assembly so it stays in the correct position
• Prevents rattling, shifting, or misalignment that can occur with a loose or broken holder
• Helps maintain proper operation of the attached part by keeping connections stable
• Common symptom: part moves, vibrates, or produces noise during operation

• One holder/mounting bracket

• Disconnect power to the appliance before beginning any repair
• Refer to the OEM parts diagram for correct orientation and mounting location
• Use appropriate hand tools and replace any damaged fasteners; do not overtighten plastic components
• If the surrounding components are damaged, inspect and replace as needed for secure installation

This drain tube routes defrost and condensate water from the evaporator to the refrigerator drain, helping prevent pooling and ice buildup behind the freezer walls. A simple replacement restores proper drainage and reduces leaks. What it does

• Channels defrost and condensation water away from the evaporator area
• Stops water from pooling or freezing inside the freezer compartment
• Helps prevent water leaks onto the cabinet floor
• Useful when the original tube is cracked, clogged, or deformed

• Disconnect power and shut off the water supply before starting
• Remove interior panels as needed to access the evaporator area; follow OEM service manual steps
• Inspect and clear the drain path; replace clamps or grommets if damaged

This is a replacement screw used to secure appliance panels and components so assemblies stay properly mounted and stable. It restores hardware that has become lost, stripped, or damaged. What it does:

• Fastens and secures panels, brackets, or trim pieces to the appliance
• Replaces missing or damaged screws that cause loose or rattling parts
• Helps maintain proper alignment of covers and access panels
• Prevents further wear from unsecured components

• Disconnect power before servicing electrical appliances to avoid shock
• Use the correct driver and size to avoid stripping the head
• Tighten until snug; do not overtighten to prevent damage to threads or plastic parts
• Replace all matching fasteners for even fit