Parts for Ge GFD85ESMN0RS: Controls & Backsplash Parts

A replacement sapphire-blue control panel that restores the front console finish and button surface for compatible GE ranges. Replaces a cracked, faded or worn control panel to help restore normal button access and appearance. What it does:

• Provides the outer panel and button surface for the range control console.
• Restores cosmetic finish and tactile feel when the original panel is cracked, scratched or faded.
• Helps resolve issues where physical damage prevents pressing buttons or obscures indicators.
• Does not include electronic control boards or touchpad circuitry unless specified.

• Disconnect power at the breaker before beginning any work.
• Remove mounting screws and trim pieces to access the console; keep hardware for reassembly.
• Handle the panel carefully to avoid cracking; align clips and screws securely during installation.
• If electronic components are attached, ensure connectors are seated and intact.

The User Interface Control Board is an OEM part for GE dryers. It acts as the user-facing control center stationed behind the console display.

Symptoms of a bad user interface control board include:

• Non-responsive or erratic function of selection buttons  
• Garbled or missing characters on the digital display
• Inability to advance cycles or access settings  
• Constant resetting of cycle parameters

Causes may stem from overextended use in demanding environments. Liquid splashes, surges, or dropped static discharges pose risks to sensitive electronics over time as well. 

This  GE replacement part is compatible with Hotpoint, RCA and select Kenmore models too.

This bracket secures the power/start button to the appliance control panel so the button stays aligned and functions correctly. Replacing a damaged bracket restores proper button fit and reliable user control. What it does:

• Holds the power/start button in place inside the control panel assembly.
• Keeps the button aligned so presses engage the switch consistently.
• Prevents the button from rattling, sticking, or falling out of the panel.
• Used when the button housing is cracked, bent, or missing mounting support.

• Disconnect power to the appliance before beginning any work.
• Remove the control panel trim or fascia to access the bracket; keep screws and fasteners organized.
• Handle internal components gently to avoid damaging the button, switch, or wiring.

8-18 hi/lo 5/8

The Handle Facia IMD and Badge Holder is an OEM part for GE dryers. It serves as the facia on the outside of the dryer door, housing important graphics and model identification. This part also acts as the secure backing and holder for the dryer badge bearing the brand name and additional details.

Causes of a bad handle facia IMD and badge holder can include cracks, breaks, or loose fittings that no longer securely hold the badge in place. 

Symptoms of a bad part include:

• Faded or worn graphics and text that are difficult to read  
• Loose or detached badge that no longer stays firmly in place
• Cracked, broken, or deteriorated facia material
• Warped or misshapen facia that no longer fits properly on the dryer door

This genuine GE replacement part is also compatible with some Roper, Hotpoint, and Kenmore dryer models.

The GE Badge is an OEM part for GE washing machines. It is an emblem installed on the exterior of the washer that identifies the manufacturer and brand. Beyond aesthetics, the badge also demonstrates authenticity and quality assurance for the appliance.

Causes of a bad badge can include damage from impact or weathering over time, loss of adhesion to the outer casing, or fading/wear of printed graphics.  

Symptoms of a bad badge include:

• Missing or loose badge that is no longer securely attached
• Faded or illegible print that fails to display the brand
• Cracks or pieces breaking off the badge surface

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Size: 8 - 18 ab.

This 10-32 screw with a hex-washer head fastens panels, brackets, or components as specified by the manufacturer. Replacing worn or missing hardware restores a secure fit and helps reduce vibration, rattling, and loosening during operation.

• Provides 10-32 machine-thread fastening at the designated mounting point
• Hex-washer head helps distribute load for a tight, reliable clamp
• Replace if the original is missing, stripped, corroded, or won't stay tight
• Helps address loose panels/brackets, vibration, or rattling noises

• Disconnect power before servicing; if working on a washer, also shut off the water supply
• Use a driver or nut driver that matches the screw head
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Reinstall any original hardware in the same order it was removed