Parts for Ge GUD27ESSM0WW: Controls & Backsplash Parts

Secures dryer panels, brackets, and internal assemblies. Replace missing, stripped, or damaged screws to restore proper alignment and prevent vibration.

Mounting screw hardware for ranges and cooktops. Replace missing, stripped, or corroded screws used to secure panels, brackets, or components.

The Board & Support Assembly is an OEM replacement part for GE washer/dryer combination laundry centers. This assembly features both the control board and its supporting structure. The control board is responsible for managing a variety of functions for both the washing machine and dryer, including cycle selection and timing, while the support secures the board in its proper position.

Causes for a malfunctioning Board & Support Assembly can include electrical issues like short circuits or power surges, as well as physical damage from impact or mishandling.

Symptoms of a bad Board & Support Assembly include:

• Difficulty in selecting or initiating wash or dry cycles
• Unresponsive or malfunctioning buttons on the control panel
• Error messages appearing on the display
• Inconsistent performance in either the washer or dryer

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Secures dryer panels and internal components to the cabinet frame. Replace if screw is stripped, missing, or loose to prevent vibration and rattling.

The CAPACITOR is an OEM part for GE washers. It works along with the motor to efficiently power the agitation and spinning functions. The capacitor stores and releases electrical current as needed to ensure a smooth wash action. 

Symptoms of a bad capacitor include:

• The washer unable to progress beyond the initial agitation cycles  
• Sluggish or struggling movements during washing or spinning
• Buzzing, humming, or crackling noises from electrical components
• Frequent tripping of circuit breakers when operating 

Causes of failure can include drying out of internal components over many years, defects in capacitor plates or wiring, or electrical surges damaging sensitive components.

Replace yours today with this genuine OEM GE part for reliable storage and delivery of current. This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Mounting bracket that secures the control assembly in your laundry center. Replace if cracked, broken, or worn to restore proper panel alignment.

The Control Panel is an OEM part for GE laundry centers. It is designed to provide convenient and easy control over selecting different wash and dry cycles, adjusting temperature settings, and setting the timer for your laundry. 

A bad Laundry Center Control Panel can occur due to electrical malfunctions, physical damage, or wear and tear over time. If the control panel becomes unresponsive or fails to operate the laundry center properly, it may be time to replace the Control Panel.

Symptoms of a bad Control Panel include:

• Unresponsive buttons or knobs.
• Inability to select or change wash and dry cycles.
• Cracks or damage to the panel. 

If you're experiencing any of these issues, it's time to replace the Control Panel with this genuine GE part to regain full control over your laundry. This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

Fix a broken, stripped, or wobbly control knob that slips or falls off. This assembly restores accurate cycle and setting selection on your console.

The Rotatory Knob is an OEM part for GE washers. It allows users to easily select and change washer settings like cycles, temperatures, and options with a simple turn. As a control interface component, the rotatory knob provides direct input to the washer's control board.

Causes of a bad rotatory knob can be normal wear from frequent use over time. Exposure to moisture, physical impacts or mishandling, and mineral buildup are other potential causes of malfunction. 

Symptoms of a bad rotatory knob include:

• Difficulty selecting or changing washer settings  
• Loose, wobbly, or unresponsive knob behavior
• Inaccurate input to the control board causes operating issues
• Cracks, splits, or broken knob components

Compatible with some Hotpoint, RCA, and Kenmore models as well.

This start button assembly is the external pushbutton on the dryer console. It lets you begin a cycle; replacing a broken or missing button restores proper engagement of the start switch and a clean, factory appearance.

• Provides the physical Start control on the console and actuates the underlying switch
• Replaces a button that is cracked, missing, loose, or won't stay in place
• Helps when the dryer won't start because the button can't press the switch
• Restores smooth, reliable button travel and appearance

• Disconnect power; if gas, shut off gas supply before moving the appliance
• Access the console, remove fasteners, release tabs, and remove the old button assembly
• Transfer any small hardware from the original as needed; align and secure the new button
• Reassemble, restore power, and test for proper button movement and start engagement

This main wiring harness connects the dryer's internal components to route power and signals, restoring proper electrical continuity so controls and motors can operate reliably. What it does

• Carries power and signal connections between the control, motor, heating assembly, and sensors
• Replaces damaged or burned wiring that can cause intermittent operation or no power to drive components
• Helps resolve symptoms like no spin, no heat (when related to wiring), or tripped fuses/thermal cutouts due to shorted leads
• Designed to match OEM terminal and connector locations for straightforward replacement

• One main wiring harness assembly

• Disconnect power at the breaker before starting any repair; this part handles live electrical connections
• Verify connectors match your dryer model and route the harness exactly as removed to avoid chafing or heat exposure
• Inspect connectors, terminals, and nearby insulation for additional damage; replace other components as needed

The Timer is an OEM part for GE electric dryers. It serves as the critical control module that monitors and regulates dryer cycle times during functions like regular, wrinkle guard, fluff and more.

Causes of a bad timer include failure of internal electronic components or wiring connections due to prolonged exposure to heat and vibration inside the dryer cylinder. Mechanical wear of buttons or dials used to program cycles may occur as well over time.

Symptoms of a bad Timer include:

• Inability to set or change desired drying times accurately
• Premature stopping or starting of cycles without user input
• Faulty time or status display windows during use
• Complete shut down requiring manual override or reset

The GE OEM part is also compatible with Hotpoint, RCA and select Kenmore models.

Dryer won't start when you press the button, or stops when released? The push-to-start switch often fails. Easy 20-minute DIY repair with video.

Control panel buttons not responding? This console wiring harness restores signal connections between your user interface and main control board.

This 27-inch fuse harness connects the dryer's thermal/fuse circuit and helps restore proper power delivery to the heating system. It provides a direct replacement for a worn or damaged harness to help re-establish safe operation. What it does:

• Carries power to the dryer's thermal cut-off/element circuit so the heater can operate
• Replaces frayed, burned or broken wiring that can cause no-heat or intermittent heating
• Restores secure terminal connections to prevent arcing and poor contact
• Supports troubleshooting for heater-related faults when the heater and thermostats test good

• Disconnect all power before servicing; verify the appliance is de-energized
• Inspect mating terminals and connectors; replace or clean damaged contacts before installation
• Route harness to match original routing and secure with existing clips or fasteners

Control board failed and washer or dryer won't start? This UI board assembly manages all washing and drying functions in your laundry center unit.

Fix washer cycles not registering or settings not responding. This 3-switch selector assembly restores control panel input. Moderate difficulty repair.

Fix control board communication errors with this RJ45 harness. Restores data exchange between boards so your laundry center operates properly again.