Parts for Ge ZIC360NXDRH: Controls & Components Parts

Freezer light not working? This light socket connects the bulb to power. Common fix for interior lighting issues. Simple installation in most models.

Outer slide rail that guides refrigerator shelves and drawers. Replace if your rail is cracked, bent, broken, or missing to restore smooth gliding movement.

Outer drawer slide rail for refrigerator pantry drawers. Guides drawer movement for smooth opening and closing. Replace if cracked, bent, or worn out.

Mounting bracket that secures the damper assembly inside your refrigerator. Replace if cracked, broken, or missing to properly support the damper component.

Molded plastic water collector that directs ice maker water to prevent pooling and leaks. Replace if cracked, broken, or missing to restore drainage.

This 3/8-inch washer is used in refrigerators to secure components and prevent loosening. Replace if washer is missing, cracked, or worn out.

A small spring-style cotter clip that secures shafts and pins to keep moving parts in place. Restores a secure fit to linkage, rods, and pivot points so components stay aligned and don't slip free during operation. What it does:

• Holds shafts, pins and rods in position to prevent components from sliding off
• Provides a spring tension lock around a grooved pin or hole for reliable retention
• Commonly used on linkage, pivots and fastener pins where a compact retaining clip is needed
• Helps stop rattling, loose connections or parts that drop out of place

• Disconnect power before servicing any electrical appliance and work with the appliance in a stable position
• Use needle-nose pliers to spread and install the clip over the pin groove; ensure it seats fully
• Inspect mating pin/hole for wear or damage and replace if deformed
• Replace with an identical clip size and style to maintain secure retention

This evaporator assembly circulates refrigerant and helps remove heat and humidity from the freezer compartment, restoring proper cold and frost control. Replaces the internal evaporator box to improve cooling performance and defrost function. What it does:

• Houses the evaporator coil to allow refrigerant evaporation and heat exchange
• Enables proper cold airflow and consistent freezer temperatures
• Supports the defrost cycle by routing meltwater to the drain system
• Commonly replaced for frost buildup, weak cooling, or abnormal freezer temperatures

• One evaporator assembly (evaporator box) as shown

• Requires access to the freezer interior; disconnect power before starting
• May require removal of shelving, panels, and the evaporator cover for access
• Follow OEM instructions for proper refrigerant and wiring handling; replace any damaged gaskets or seals

Refrigerator not cooling or freezing over? The defrost heater melts ice buildup on evaporator coils to restore proper airflow and temperature control.

Replace your refrigerator's freezer light shield to protect the bulb and restore proper illumination. Confirm fit with your model number before ordering.

Guides defrost water into the drain opening to prevent puddling and ice buildup. Replace if cracked, broken, or missing to keep water flowing properly.

Fix fresh food section freezing or not cooling issues with this air damper assembly. Controls airflow between freezer and refrigerator compartments.

Secures heater and sensor wiring to the evaporator area in your refrigerator. Replace if cracked, broken, or missing to maintain proper wire routing.

Left-side evaporator baffle directs cold air flow in the freezer compartment. Replaces cracked, broken, or missing baffles to restore proper airflow.

Fixes ice buildup in freezer and warm fresh food compartment. This bimetal defrost thermostat controls heater cycles to prevent frost accumulation.

Fix refrigerator cooling issues with this evaporator jumper tube. Connects evaporator sections in the sealed system. Professional repair recommended.

Freezer getting too warm during defrost? This defrost thermostat regulates evaporator coil temperature. Moderate DIY repair with wire splicing.

Protects and directs fresh food compartment light. Replace if cracked or discolored to restore proper illumination. Verify fit with your model number.

Collects defrost water under your refrigerator. Replace if cracked, leaking, or missing to prevent water damage and moisture buildup on your floor.

Evaporator drip pan that catches and channels defrost water away from the freezer evaporator. Replace if cracked, damaged, or missing to restore drainage.

This HMI control assembly is the user interface board that lets you select and display settings on the appliance, restoring responsive controls and proper display feedback for normal operation. What it does:

• Provides the touch/key inputs and display signals for the appliance control system
• Registers user commands (cycle selection, temperature, timers) and sends them to the main control
• Restores missing or unresponsive front-panel controls and display feedback
• Can resolve symptoms like non-responsive buttons, blank or erratic display, or failure to accept user inputs

• Always disconnect power to the appliance before servicing to avoid electrical shock
• Handle the board carefully to avoid static damage; use anti-static precautions if available
• Installation typically requires removing the control panel or trim; retain fasteners and gaskets for reassembly

Replaces a cracked or broken drain trap in your refrigerator. Installs on the drain hose at the back of the unit. Use pliers to remove the old trap.