Parts for Ge GFW550SPR5RS: Controls Dispenser Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This power cord fix belt is a small cord-retaining strap that secures the appliance power cord to the cabinet. It helps keep the cord in place to reduce strain on the cord connection and maintain a reliable power connection. What it does:

• Holds the power cord firmly against the appliance frame to prevent tugging on the wiring
• Reduces movement that can loosen or wear the cord connection over time
• Helps prevent intermittent power or connection issues caused by a shifted cord
• Keeps cord routing neat and reduces stress at the plug/body interface

• One power cord fix belt

• Always disconnect power before accessing the cord or electrical panels
• Typically installs behind a rear access panel or at the cord entry point; basic tools may be required
• Position so the cord is secure but not pinched; replace if cracked or brittle

This is a small retaining clip used to secure a fixed line or hose inside a dryer. It snaps onto the line to hold it firmly in position against the dryer frame or panel, preventing movement during operation. Replace this clip if it is cracked, broken, or missing, which can cause internal lines to shift or disconnect.

If your washer's display is blank, buttons don't respond, or cycles won't start, the user interface board is likely failed. Requires panel removal.

Fix an unresponsive or misaligned power button with this washer control panel support bracket. Restores proper button position and contact. DIY part.

This dispenser drawer handle replaces the front pull for a refrigerator dispenser, restoring a secure grip and original appearance. Its sapphire blue finish matches select GE refrigerator dispenser assemblies. What it does:

• Replaces a cracked, broken, or missing dispenser drawer handle to allow normal opening and closing of the dispenser drawer
• Provides a finished edge and grip for the dispenser area to reduce snagging and improve usability
• Restores the cosmetic appearance of the dispenser with the original sapphire blue color
• Helps keep the dispenser drawer aligned and easy to access when properly installed

• Designed to snap or screw into the dispenser drawer; check your refrigerator's service manual or parts diagram for exact fastener locations
• Turn off power to the refrigerator and remove contents from the dispenser area before beginning work
• Handle small plastic parts carefully to avoid cracking; use a non-marring tool if prying is required
• If fasteners are damaged or missing, replace them with OEM-recommended hardware

The GE Badge is an OEM part for GE washing machines. It is an emblem installed on the exterior of the washer that identifies the manufacturer and brand. Beyond aesthetics, the badge also demonstrates authenticity and quality assurance for the appliance.

Causes of a bad badge can include damage from impact or weathering over time, loss of adhesion to the outer casing, or fading/wear of printed graphics.  

Symptoms of a bad badge include:

• Missing or loose badge that is no longer securely attached
• Faded or illegible print that fails to display the brand
• Cracks or pieces breaking off the badge surface

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Fix a washer that won't fill, fills slowly, or won't stop filling. This water inlet valve controls hot and cold water flow into your washing machine.

This is a manual dispenser drawer assembly for a front-load washer. It holds and dispenses detergent, fabric softener, and bleach during the appropriate wash cycle phases. Replace this drawer if it is cracked, warped, clogged with detergent buildup that cannot be cleaned, or if it no longer slides smoothly in and out of the dispenser housing.

Replacement screw set for securing the front panel to your dryer or washer chassis. Install when original screws are stripped, missing, or damaged.

Replace a missing or corroded ground screw to restore proper electrical grounding. Prevents shock hazards and ensures safe appliance operation. Quick fix.

This shoulder bolt is a precision fastener that positions and secures moving parts while allowing controlled rotation or sliding. It restores proper alignment and smooth motion for assemblies that rely on a fixed shoulder. What it does:

• Acts as a locating pin and fastener to hold components in alignment while permitting rotation or sliding
• Supports rotating or sliding parts and reduces wear by providing a machined bearing surface
• Helps stop vibration and play that can cause noise, squeaks, or misaligned panels
• Commonly used where a bolt head and a smooth bearing surface are both required

• Inspect mating parts for wear and replace if the shoulder or hole is damaged
• Hand-start threads to avoid cross-threading; tighten to secure without over-torquing
• Disconnect power and follow appliance-specific safety instructions before servicing

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.