Parts for Thermador PCG366G-01: Controls Parts

This gas pressure regulator controls and stabilizes incoming supply pressure to the appliance manifold, helping ensure consistent burner flames and reliable ignition. Replace if the original regulator is sticking or no longer maintaining correct pressure.

• Regulates incoming gas to the appliance's rated manifold pressure
• Helps maintain even flame height and proper combustion
• Supports reliable burner ignition and reduces flame-out from pressure swings
• Common symptoms include weak or uneven flames, yellow tipping, burners not lighting or not staying lit, or flames that are too high

• Disconnect electrical power and shut off the gas supply before servicing
• Observe the flow-direction arrow; install with outlet toward the appliance manifold
• Use approved gas-rated thread sealant on male threads only and leak-test all joints with a non-corrosive solution after installation

The Solenoid Valve is an OEM part for Bosch ranges. Located inside the control panel, the solenoid valve regulates gas to individual burners during the cooking cycle. It opens and closes electrically to direct fuel when its paired control knob is turned on.

Symptoms of a bad solenoid valve include:

• Inability to ignite or maintain a flame on specific burners 
• Burners failing to respond to control settings
• Hesitation or delay in burner engagement
• Range functions in an unpredictable manner

Causes can involve normal wear of moving internal parts, mineral buildup inhibiting valve movement, or physical damage. Failure reduces the range's functionality and safety.

This OEM Bosch part is also compatible with Thermador and Gaggenau models.

The Spark Ignition Switch is an OEM part for Bosch ranges and cooktops. It controls the ignition of surface burner flames by emitting an electrical spark when activated.

Causes of a bad switch can be general wear and fatigue over thousands of start cycles. Exposure to moisture, dust or metal debris could also damage electrical components internally.

Symptoms of a bad spark ignition switch include:

• Burners failing to light even when valves are turned on
• Intermittent or irregular lighting of some burners
• No electrical sparks emitted from the ignition electrode

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Replacement water inlet valve that controls an appliance's incoming water flow for reliable fill and cycle operation. Replacing a faulty valve can stop no-fill, slow-fill, or continuous-fill issues and restore normal performance. What it does:

• Opens and closes to regulate water entering the appliance during fill cycles.
• Helps ensure correct water levels for proper washing or rinsing.
• Common symptom fixer for appliances that won't fill, fill slowly, or keep filling.
• May cause visible leaks at the valve or trigger fill-related fault behavior if failed.

• Turn off power and shut off the water supply before starting any work.
• Open a cycle or relieve pressure to drain residual water before removing the old valve.
• Inspect and replace any worn seals or inlet hoses when installing the new valve.
• Follow the appliance service manual for specific removal/installation steps.

This display is the user interface module that shows cycle status, settings and error indicators so you can read and control the appliance from the front panel. It restores visible feedback and menu information for normal operation. What it does

• Provides the visible display for cycle progress, timers and selected options
• Shows error codes and status messages to help identify issues
• Works with the appliance control board to update settings and user inputs
• Restores readable display after a failed or cracked panel

• Disconnect power to the appliance before starting work to avoid shock or damage
• Replacement typically requires removal of the front control or console panel; handle the display lens and ribbon connectors carefully
• Keep screws and small fasteners organized for reassembly

This facia panel is the exterior trim that covers and protects the appliance control area, restoring a clean, finished look and protecting buttons and electronics from everyday wear. It's a direct-replacement cosmetic and protective part. What it does

• Covers the control area and provides the finished front look of the appliance.
• Protects buttons, switches, and the control board from dirt, spills, and impact.
• Replaces cracked, scratched, warped, or otherwise damaged front trim.
• Helps restore proper fit and alignment of the control assembly for normal operation.

• One facia panel

• Disconnect power (unplug or switch off circuit breaker) before starting any work.
• Remove any outer trim or door panels as needed to access and remove the old facia; keep screws and fasteners for reuse if undamaged.
• Handle the new facia carefully to avoid scratching; align mounting tabs and secure with original hardware.

Restore confident control of your appliance with this replacement control knob. It slides onto the control shaft to provide a secure, accurate grip so you can easily select settings when the original knob is cracked, stripped, or missing. What it does:

• Attaches to the control shaft to select temperature, cycle, or power settings
• Restores positive engagement and smooth turning of the control
• Helps resolve a loose, wobbly, or slipping selector
• Replaces knobs that are cracked, broken, or won't stay on

• One control knob

• Disconnect power; for gas appliances, also shut off the gas supply before servicing
• Pull the old knob straight off the shaft; if your model uses a set screw or clip, loosen/remove it first
• Align the new knob with the shaft and press on firmly; retighten any set screw if present
• Test operation to ensure the knob engages and turns the control smoothly