Parts for Electrolux E36GC70FSS2: 03 - Cook Top Parts

This main top is the replacement cooktop panel that provides a stable, finished surface for burner components and grates. It restores proper mounting and appearance for damaged, bent, or corroded range tops. What it does

• Replaces a warped, dented, or rusted cooktop surface so burners and grates sit level
• Supports burner heads, drip pans, and grates to ensure correct alignment
• Restores the range's finished appearance where the original top is damaged or cosmetically worn
• Helps prevent heat and debris from reaching internal components under the cooktop

• One main top/cooktop panel as pictured

• Disconnect power (and gas if applicable) and follow the appliance manufacturer's safety procedures before starting
• Remove burner grates, burner heads, and any trim pieces to access mounting screws; keep hardware organized for reassembly
• Handle carefully to avoid scratching or bending the replacement top during installation

This burner cap is the replacement top piece for a surface gas burner, restoring proper flame shape and heat distribution for reliable cooking. It helps protect the burner head and keeps the flame centered for consistent performance. What it does

• Centers and shapes the burner flame for even heating across cookware
• Protects the burner head from spills and debris that can block ports
• Helps prevent yellow or irregular flames caused by a damaged or misaligned cap
• Common symptom: uneven or weak flame, burner flame that drifts or won't stay lit

• Turn off the range and ensure all surfaces are cool before servicing
• Lift off the old cap from the burner head; no tools are typically required
• Set the new cap flat and centered on the burner head so it sits flush
• If problems persist after replacement, inspect the burner head and ports for blockage

This replacement power cord restores electrical connection to your appliance so it powers on safely and reliably. Designed as a direct-fit electrical cord to replace damaged, cut, or worn factory cords. What it does

• Provides the primary AC power connection from the wall outlet to the appliance.
• Replaces frayed, cracked, or damaged cords that can cause intermittent power or safety hazards.
• Helps resolve no-power or intermittent-power symptoms when the cord is the root cause.
• Restores a secure connection at the appliance and outlet when properly installed.

• Disconnect power at the breaker or unplug the appliance before starting any work.
• Route the cord through the appliance's strain relief and secure all wiring connections per the appliance's wiring diagram.
• Use insulated tools and avoid pinching or sharp bends in the cord; replace strain reliefs if damaged.

This replacement control knob restores smooth, accurate adjustment of your appliance's settings when the original is worn, cracked, or missing. Get a secure grip and the original look with a direct-fit knob that installs in seconds.

• Presses onto the control stem to actuate the underlying switch or valve
• Fixes knobs that are stripped, loose, wobbly, hard to turn, or missing
• Helps when the pointer no longer aligns with settings or the knob spins freely
• Direct-fit design maintains the original feel and operation

• Unplug the appliance or switch off power at the breaker before servicing
• Pull the old knob straight off; avoid bending the control shaft
• Align the new knob's insert with the flat/key on the stem and push fully into place
• Verify smooth rotation and proper engagement of the control

Note: Quantity of two brackets

This is an authentic OEM replacement bracket locking screw sourced directly from the manufacturer for use on range tops. The stovetop bracket is attached to the stovetop and the stove body. This locking screw is a fully threaded 2.1-inch screw. If this screw becomes loose or rusted, it should be removed and replaced to ensure the stovetop remains fully seated and in good working condition. If the screw is missing, the stovetop bracket will not be fully functional, and the stovetop could become loose. To start, disconnect the power and gas from the unit before replacing the screw on the bracket. Make certain the stove burners are not hot. Remove the burner grates, burner caps, and control knobs. Lift the range top cover. Locate the mounting bracket on the wall unit. If the screw is in the bracket but has rusted, use a screwdriver to remove the missing screw. Set the nut aside for use on the new screw. Install the new screw and the nut from the last screw. Check the bracket alignment before tightening the screw. Tighten the screw to the nut. Lower the stovetop and reconnect the power and gas. This bracket locking screw is a heavy-duty 2.1-inch silver metal screw. It is designed for use on gas ranges manufactured by Frigidaire, Kenmore, Electrolux, and Crosley.

Specs: 10-32 X 0.375

This is a #8 screw, 0.500 inch long, used to secure panels and components in appliances. It provides a correct-fit fastener for repairs where the original #8 x 1/2" screw was required, restoring proper assembly and stability. What it does:

• Fastens trim, panels, brackets and small components where a #8 x 1/2" screw is specified
• Holds parts securely to prevent rattling, gaps or loose panels
• Replaces worn, stripped or missing screws to restore proper fit
• Appropriate for common interior and exterior appliance mounting points

• Use the correct screwdriver (typically Phillips) and avoid over-tightening to prevent strip or damage
• Disconnect power and follow appliance manufacturer safety instructions when accessing internal parts