Parts for Electrolux E36GC70FSS3: 02 - Cook Top Parts

This main top is the replacement cooktop panel that provides a stable, finished surface for burner components and grates. It restores proper mounting and appearance for damaged, bent, or corroded range tops. What it does

• Replaces a warped, dented, or rusted cooktop surface so burners and grates sit level
• Supports burner heads, drip pans, and grates to ensure correct alignment
• Restores the range's finished appearance where the original top is damaged or cosmetically worn
• Helps prevent heat and debris from reaching internal components under the cooktop

• One main top/cooktop panel as pictured

• Disconnect power (and gas if applicable) and follow the appliance manufacturer's safety procedures before starting
• Remove burner grates, burner heads, and any trim pieces to access mounting screws; keep hardware organized for reassembly
• Handle carefully to avoid scratching or bending the replacement top during installation

This burner cap is the replacement top piece for a surface gas burner, restoring proper flame shape and heat distribution for reliable cooking. It helps protect the burner head and keeps the flame centered for consistent performance. What it does

• Centers and shapes the burner flame for even heating across cookware
• Protects the burner head from spills and debris that can block ports
• Helps prevent yellow or irregular flames caused by a damaged or misaligned cap
• Common symptom: uneven or weak flame, burner flame that drifts or won't stay lit

• Turn off the range and ensure all surfaces are cool before servicing
• Lift off the old cap from the burner head; no tools are typically required
• Set the new cap flat and centered on the burner head so it sits flush
• If problems persist after replacement, inspect the burner head and ports for blockage

This replacement power cord restores electrical connection to your appliance so it powers on safely and reliably. Designed as a direct-fit electrical cord to replace damaged, cut, or worn factory cords. What it does

• Provides the primary AC power connection from the wall outlet to the appliance.
• Replaces frayed, cracked, or damaged cords that can cause intermittent power or safety hazards.
• Helps resolve no-power or intermittent-power symptoms when the cord is the root cause.
• Restores a secure connection at the appliance and outlet when properly installed.

• Disconnect power at the breaker or unplug the appliance before starting any work.
• Route the cord through the appliance's strain relief and secure all wiring connections per the appliance's wiring diagram.
• Use insulated tools and avoid pinching or sharp bends in the cord; replace strain reliefs if damaged.

This replacement control knob restores safe, tactile control for a worn, cracked, or missing stove/oven or appliance control. It provides a simple push-on replacement so you can accurately select settings and operate the appliance. What it does:

• Replaces a damaged, cracked, loose, or missing control knob
• Allows clear selection of temperature or function settings
• Provides a secure push-on fit to the control shaft for reliable operation
• Helps prevent accidental changes from worn or slippery knobs

• Disconnect power (and gas if applicable) before servicing the appliance.
• Align the knob's opening with the control shaft splines and push straight on until fully seated.
• If the knob does not seat easily, check shaft condition and correct spline alignment—do not force.

Note: Quantity of two brackets

Specs: 10-32 X 0.375

This is a #8 screw, 0.500 inch long, used to secure panels and components in appliances. It provides a correct-fit fastener for repairs where the original #8 x 1/2" screw was required, restoring proper assembly and stability. What it does:

• Fastens trim, panels, brackets and small components where a #8 x 1/2" screw is specified
• Holds parts securely to prevent rattling, gaps or loose panels
• Replaces worn, stripped or missing screws to restore proper fit
• Appropriate for common interior and exterior appliance mounting points

• Use the correct screwdriver (typically Phillips) and avoid over-tightening to prevent strip or damage
• Disconnect power and follow appliance manufacturer safety instructions when accessing internal parts