Parts for Amana AGG222VDB1: 01 - Cooktop Parts

Color: Black

Color: White

This backguard is the metal rear panel that mounts behind the range controls to protect internal components and finish the appliance's rear appearance. It restores a secure, finished back surface and helps keep wiring covered. What it does:

• Covers and protects control housing, wiring and components at the rear of the range
• Restores a finished appearance after damage, corrosion or previous part removal
• Helps maintain correct spacing and mounting for the control console
• Prevents debris from entering the control area

• Disconnect power to the appliance before beginning any work to avoid shock
• May require removal of the cooktop or control console and several mounting screws
• Use caution handling sheet metal edges; wear gloves to prevent cuts

Color: Black. Measures about 2 inches in diameter. For biscuit use WP98008208. For white use WP98006102. Sold individually.

Color: White. This knob measures about 2 inches in diameter. For black use WP98006100. For biscuit use WP98008208. Sold individually.

This black thermostat knob replaces a worn or broken control knob so you can set oven/cooktop temperatures accurately and safely. It restores a solid grip and clear position indication for reliable temperature control. What it does:

• Replaces a damaged or missing thermostat/control knob so you can adjust temperature settings
• Fits onto the control shaft to provide secure grip and clear pointer alignment
• Helps correct symptoms like a cracked, loose, or hard-to-turn knob or unclear temperature position
• Restores safe, consistent manual control of the temperature selector

• Disconnect power to the appliance before servicing to avoid shock or injury
• Pull the old knob straight off the control shaft; no special tools typically required
• Align the knob's internal opening with the control shaft and push on until fully seated
• If the knob feels loose after installation, check the control shaft and coupling for wear and replace as needed

This thermostat control knob replaces a worn or broken temperature selector knob. It restores a clean look and positive feel so you can reliably set cooking temperatures. White finish matches the original appearance. What it does:

• Attaches to the thermostat shaft to select temperature settings
• Replaces knobs that are cracked, stripped, loose, missing, or hard to read
• Restores smooth turning and a secure fit on the control stem
• Helps ensure the pointer aligns with the temperature markings

• One white thermostat control knob

• Turn all controls off and allow the appliance to cool before service; disconnect power if accessing any internal panels
• Pull the old knob straight off the thermostat shaft; avoid prying on the panel
• Align the new knob's hub with the shaft and press straight on until fully seated
• Verify pointer alignment with the temperature scale and re-orient if needed

Color: Black. Includes one double grate. For gray order WPW10180089.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

The Clip is an OEM component specifically designed for Whirlpool ranges. This clip plays a role in securely holding and mounting components within the appliance. 

The clip is designed to securely grip parts in place, preventing unwanted movement or dislodging that could impact the operation or result in damage. It allows for components to be effortlessly installed while remaining firmly affixed. 

Causes of a bad clip can include wear and tear over time, damage due to excessive force or impact, or deterioration from heat exposure. 

Symptoms of a bad clip include: 

• Loose or detached components inside the appliance 
• Increased vibration or unwanted noise during operation
• Components that are not sitting securely or properly installed
• Difficulty accessing or removing parts that rely on the clip 

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Factory replacement screw that secures appliance components and hardware. Use it to replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and help prevent loosening or damage from vibration.

• Fastens brackets, panels, or internal parts at the original mounting points
• Replaces worn or missing hardware to correct loose or misaligned components
• Helps reduce vibration-related noise and movement
• Matches the original thread and length specified for the application

• Disconnect power; shut off water or gas if applicable before servicing
• Compare to the original for thread and length match before installation
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• Reuse any original spacers/washers if present; replace if damaged

This light switch is the replacement rocker-style control that turns the oven/cabinet light on and off so you can safely check cooking progress without opening the door. It provides a direct, user-facing switch function and restores reliable light control. What it does

• Replaces a faulty rocker light switch that won't turn the oven/cabinet light on or off
• Restores responsive on/off control for the interior light so you can view contents without opening the door
• Helps eliminate intermittent or non-working light due to a worn or failed switch
• Fits into the original switch opening and interfaces with the existing wiring harness

• One (1) light switch (rocker-style)

• Disconnect power to the appliance before beginning any repair to avoid electric shock
• May require removing the control/inner panel or light housing to access the switch—use appropriate hand tools
• Verify wire locations and harness connection before removal; swap wires one at a time or photograph connections

This burner head sits on the cooktop and channels gas through precision ports to produce an even flame. Replacing a worn or clogged head restores quick ignition and consistent heat across the burner.

• Mixes gas and air and distributes the flame evenly around the burner
• Works with the spark igniter for reliable lighting
• Can address delayed ignition or a burner that won't light due to clogged or damaged ports

• Disconnect power and shut off the gas supply; allow the surface to cool completely
• Remove the grate and burner cap; remove the center retaining screw and lift off the old head
• Clean the orifice and igniter area; align and seat the new head flat over the orifice and igniter
• Reinstall the cap and grate; restore utilities and verify ignition and a uniform flame pattern (do not enlarge or poke burner ports)

Color: Black. Measures about 3 inches in diameter. For grey use WP98017461.