Parts for Bosch HEI7032U/01: Cooktop Parts

This heating element heats air inside the dryer so laundry dries efficiently. It replaces a failed or damaged heating assembly to restore normal heat generation and drying performance. What it does:

• Produces the heat that dries clothes when the dryer runs
• Commonly related to no-heat or low-heat dryer symptoms
• Can fail open or short, causing intermittent heating or tripped breakers
• Works with the dryer's thermostat and thermistor to control operating temperature

• Disconnect power at the breaker before inspecting or replacing the element
• Handle with care to avoid damaging terminals or the element coil; wear gloves and eye protection
• Verify wiring placement and secure all fasteners; replace any damaged insulation or grommets

This is a replacement oven control board manufactured by Bosch. The oven control board is the oven's brain and handles all the functions. It also includes the display and provides users with the ability to control functionality, like bake and broil, setting timers, and more. While the oven control board does not include moving parts, heat and moisture can damage soldered components and lead to failure. Signs that the control board may need to be replaced include lack of information on the display, inability to control specific functions, or complete lack of operability. Note that this part is often misdiagnosed, so make sure to check the old board's operability with a multimeter before replacing it. To replace the oven control board, first remove the exterior cowling. Locate the wiring harness and disconnect it before removing the mounting screws. Install the replacement part following these steps in reverse.This genuine OEM part is sold individually. It only fits Bosch Thermador ovens.

This pushbutton switch controls power to the appliance circuit. When pressed, it opens or closes the electrical path to turn the function on or off, restoring reliable button response and consistent operation.

• Controls on/off power for the selected function
• Worn or stuck switch can cause no response when pressing the button
• Intermittent, delayed, or stuck-on operation may indicate switch failure
• Physical damage or heat discoloration on terminals are common failure signs

• Disconnect power before service to avoid electrical shock
• Note wire positions or photograph connections before removal
• Transfer wires firmly to the new switch; ensure terminals are fully seated
• Test function before reassembling panels

This replacement push-button switch restores reliable user input for compatible Bosch appliances, letting controls respond correctly and safely. It replaces a worn or non-responsive front-panel switch to help restore normal operation. What it does

• Sends the user's on/off or function selection signal to the appliance control board
• Commonly replaces a switch that is stuck, intermittently responsive, or unresponsive
• Helps stop false inputs or unintended starts caused by a failing button
• Works as a direct-fit control component when matched to the exact part number

• One replacement push-button switch

• Disconnect power (unplug appliance or shut off circuit breaker) before servicing
• Access may require removing a control panel; keep fasteners and trim parts separate
• Handle electrical connectors carefully and match wiring positions when reassembling

This sealing ring creates a watertight seal in the dishwasher pump/motor area to help prevent leaks and protect the motor assembly. It's a small but essential replacement for worn or damaged seals. What it does:

• Seals pump housing joints to stop water leaks beneath the dishwasher
• Helps maintain proper water pressure and circulation for cleaning performance
• Prevents water from reaching the motor and electronics, reducing risk of damage
• Replaces brittle, cracked, or flattened seals that commonly cause under-unit leaks

• One sealing ring

• Turn off power and water to the appliance before starting any repair
• Inspect mating surfaces and clean away debris or buildup before installing the new ring
• Lubricate the seal lightly with OEM-recommended lubricant or a thin film of water if needed to ease installation
• If multiple seals or gaskets show wear, replace them together to ensure a complete seal.

A round control knob that lets you easily select and adjust heat settings on your appliance. Replaces a worn, cracked, or missing knob to restore safe, tactile control of the burner or oven function. What it does:

• Provides a secure grip for turning appliance controls and selecting heat levels
• Replaces stripped or broken knobs that no longer engage the control shaft
• Helps stop accidental changes from loose or missing knobs
• Restores clear tactile clicks and detents for precise setting selection

• High-level push-on installation: remove the old knob by pulling straight off the splined shaft, align the new knob, and push on until fully seated
• Make sure the control is in the OFF position before removing or installing a knob
• Disconnect power and gas to the appliance before servicing controls; allow hot surfaces to cool
• If the knob does not seat smoothly, verify shaft orientation and spline match; do not force or modify the knob