Parts for Bosch HEI7132U/05: Cooktop Parts

This replacement heating element warms the air inside an electric dryer so clothes dry efficiently. Use it to restore normal heating when the dryer runs but does not produce sufficient heat. What it does:

• Heats incoming air that circulates through the dryer drum to evaporate moisture
• Commonly used when the dryer runs but produces little or no heat
• Works with the dryer's internal blower and venting to maintain normal drying cycles
• Should be checked alongside thermal fuses and thermostats when diagnosing heating problems

• One heating element assembly

• Disconnect power at the circuit breaker before accessing the heater assembly; this part can be connected to high voltage
• Replacement typically requires access to the dryer's rear or lower front panel and basic hand tools
• Avoid touching element terminals or sharp sheet-metal edges; follow OEM instructions for secure electrical and mounting connections
• If the dryer still doesn't heat after installation, test or replace related components (thermal fuse, high-limit thermostat, wiring) as needed

This is a replacement oven control board manufactured by Bosch. The oven control board is the oven's brain and handles all the functions. It also includes the display and provides users with the ability to control functionality, like bake and broil, setting timers, and more. While the oven control board does not include moving parts, heat and moisture can damage soldered components and lead to failure. Signs that the control board may need to be replaced include lack of information on the display, inability to control specific functions, or complete lack of operability. Note that this part is often misdiagnosed, so make sure to check the old board's operability with a multimeter before replacing it. To replace the oven control board, first remove the exterior cowling. Locate the wiring harness and disconnect it before removing the mounting screws. Install the replacement part following these steps in reverse.This genuine OEM part is sold individually. It only fits Bosch Thermador ovens.

This pushbutton switch controls power to the appliance circuit. When pressed, it opens or closes the electrical path to turn the function on or off, restoring reliable button response and consistent operation.

• Controls on/off power for the selected function
• Worn or stuck switch can cause no response when pressing the button
• Intermittent, delayed, or stuck-on operation may indicate switch failure
• Physical damage or heat discoloration on terminals are common failure signs

• Disconnect power before service to avoid electrical shock
• Note wire positions or photograph connections before removal
• Transfer wires firmly to the new switch; ensure terminals are fully seated
• Test function before reassembling panels

This replacement push-button switch restores reliable user input for compatible Bosch appliances, letting controls respond correctly and safely. It replaces a worn or non-responsive front-panel switch to help restore normal operation. What it does

• Sends the user's on/off or function selection signal to the appliance control board
• Commonly replaces a switch that is stuck, intermittently responsive, or unresponsive
• Helps stop false inputs or unintended starts caused by a failing button
• Works as a direct-fit control component when matched to the exact part number

• One replacement push-button switch

• Disconnect power (unplug appliance or shut off circuit breaker) before servicing
• Access may require removing a control panel; keep fasteners and trim parts separate
• Handle electrical connectors carefully and match wiring positions when reassembling

This rubber grommet cushions and seals appliance components to reduce vibration, protect wiring or hoses, and help maintain a tight fit where parts pass through a panel or mounting point. It's a small but important wear item. What it does:

• Cushions vibrations and prevents metal-to-metal contact that can cause noise or wear
• Seals openings to help keep moisture, debris, and dust out of sensitive areas
• Protects hoses, wires, and tubing from chafing where they pass through panels
• Helps hold small components or fasteners in place at their mounting points

• Replace with the same size and shape grommet to ensure a proper fit and seal
• Inspect the surrounding area for wear or damage before installing
• Use basic hand tools; disconnect power and water before servicing
• If access requires disassembly, keep fasteners organized and follow OEM guidelines

This sealing ring creates a watertight seal in the dishwasher pump/motor area to help prevent leaks and protect the motor assembly. It's a small but essential replacement for worn or damaged seals. What it does:

• Seals pump housing joints to stop water leaks beneath the dishwasher
• Helps maintain proper water pressure and circulation for cleaning performance
• Prevents water from reaching the motor and electronics, reducing risk of damage
• Replaces brittle, cracked, or flattened seals that commonly cause under-unit leaks

• One sealing ring

• Turn off power and water to the appliance before starting any repair
• Inspect mating surfaces and clean away debris or buildup before installing the new ring
• Lubricate the seal lightly with OEM-recommended lubricant or a thin film of water if needed to ease installation
• If multiple seals or gaskets show wear, replace them together to ensure a complete seal.