Parts for Bosch NEM3064UC/01: Cooktop Parts

Cracked or chipped cooktop glass? This glass-ceramic surface replaces broken cooktop tops. Moderate difficulty—requires lifting unit to access screws.

Seals the gap between your cooktop and countertop to prevent spills from leaking underneath. Replace when cracked, loose, or worn to maintain protection.

This sealing is a molded rubber gasket that restores a watertight, airtight seal to the appliance, helping prevent leaks and maintain proper temperature control. Replace a worn or damaged seal to stop moisture escape and reduce energy loss. What it does:

• Forms a continuous seal around the door or access opening to prevent water or air leaks
• Helps keep internal temperatures stable for consistent performance
• Reduces condensation and prevents water pooling beneath the appliance
• Can stop symptoms such as leaks, poor temperature control, or excessive frost/condensation

• One molded rubber sealing/gasket

• Inspect the door/frame for damage and clean mating surfaces before installing the new seal
• Gasket typically presses or snaps into a channel; no special tools usually required, but a soft tool can help seat it evenly
• If adhesive is present on the original seal, use the appropriate adhesive rated for the appliance
• Unplug the appliance or shut off power/water supply before starting any repair; follow all safety instructions in the owner's manual

Replace a faulty cooktop energy regulator when burners won't heat properly or cycle inconsistently. This control regulates power to surface elements.

Replace a faulty cooktop energy regulator when burners won't heat properly or cycle inconsistently. This control regulates power to surface elements.

This is a plastic or molded housing that encloses and protects a switch assembly on a range or oven. It serves as the structural case that holds the switch components securely in place. Replace this housing if it is cracked, melted, or broken, which can leave internal switch parts exposed or cause the switch to malfunction.

Replace your cooktop heating element when a burner zone stops heating or heats unevenly. This radiant surface element restores proper cooking performance. Verify fit with your model number before ordering.

Replace your cooktop heating element when a burner zone stops heating or heats unevenly. This radiant surface element restores proper cooking performance. Verify fit with your model number before ordering.

Heating element for electric cooktops. Replace when the element no longer heats evenly or fails to reach temperature. Verify compatibility with your model.

Burner not heating or taking too long to boil water? This heating element assembly restores proper temperature output. Common fix for cooktops and ranges.

Burner won't heat? This radiant element restores even heating to your cooktop. Direct replacement for damaged or non-heating surface burners.

A small chassis knockout protector that shields wiring and components where factory knockout holes are removed. Helps prevent wire abrasion and keeps openings tidy for safe appliance operation. What it does:

• Fits into a chassis knockout to protect wiring from sharp sheet-metal edges
• Helps prevent cable chafing and short circuits by covering exposed openings
• Keeps out debris while allowing routed harnesses to pass through the cabinet
• Commonly used where service or modifications require a sealed knockout

• One chassis knockout protector

• Install by pressing the protector into the knockout until it seats securely
• Ensure wiring is routed through the protector and not pinched between metal edges
• Disconnect power before servicing appliance to avoid shock or injury

90-degree connector cable for ovens and cooktops. Replaces damaged, frayed, or missing connectors. Essential for secure electrical connections.

This is an insert component designed for use in a range vent hood. It fits into the hood housing to support proper airflow or provide a finished appearance on the unit's exterior. Replace this insert if it is damaged, warped, or missing, which can affect the fit and function of the vent hood.

Spacer component for electric cooktops. Installs between cooktop elements or panels to maintain proper spacing. Replace if cracked, broken, or missing.

Replace a cracked, broken, or missing control knob on your cooktop. This knob installs on the control panel to adjust burner temperature settings.

Razor blade with cooktop cleaner

Cooktop fixing kit secures your appliance to the countertop. Replace if brackets are damaged or during reinstallation. Verify fit with your model number.

Coding plug for electric cooktops. Installs in the control system to configure settings. Replace if cracked, broken, or missing to restore proper operation.

Hardware set with screws and nuts for cooktop assembly and component mounting. Replaces missing, stripped, or corroded fasteners during repairs.