Parts for Ge PHB920SJ7SS: Cooktop Parts

This induction control assembly replaces the main control board that manages cooktop heating and user commands, restoring normal cooktop operation and responsive control. Designed as a direct-fit replacement for the induction cooktop control module. What it does:

• Regulates power to the induction element(s) so cookware heats correctly
• Interprets touch/display commands and relays settings to the cooktop
• Helps resolve symptoms like unresponsive controls, no heat from an induction zone, or intermittent heating
• Works with the cooktop's safety and sensor feedback to maintain proper operation

• One induction control assembly

• Disconnect power at the breaker before accessing the cooktop; verify power is off with a meter
• Handle the glass cooktop and electronics carefully to avoid damage; use proper protective gear
• Follow the oven/cooktop service manual for disassembly order and connector locations

Generator board assembly that produces the high-voltage spark used to ignite gas burners on compatible ranges and cooktops, helping restore reliable ignition and reduce continuous clicking or no-spark conditions. What it does:

• Generates the spark that lights surface burners and/or the oven burner on gas cooktops and ranges.
• Can stop or reduce continuous clicking with no ignition when the module fails.
• May cause one or more burners to stop sparking or ignite intermittently.
• Works with the range's ignition switches and electrode wires to coordinate safe ignition.

• Disconnect electrical power and shut off the gas supply before starting any work.
• Photograph or label wire locations before disconnecting to ensure correct reconnection.
• Handle the board and connector pins carefully to avoid damage; avoid touching components with bare hands or tools.

This 250V, 20A line fuse safeguards the appliance's power circuit by interrupting current during an overload or short. Replacing a blown fuse can restore power once the root cause is corrected.

• Opens the circuit if current exceeds 20 amps or a short occurs
• Helps protect internal wiring and control components from damage
• Typical blown-fuse symptoms: no power, dead display, won't start
• Restores line continuity after the underlying issue is resolved

• Disconnect power at the breaker/unplug before servicing
• Replace only with the same rating (250V, 20A); never bypass or upsize the fuse
• If a new fuse blows again, stop and diagnose the underlying fault before further replacement

This is a replacement range top glass assembly that restores the cooktop surface and protects internal components while keeping your rangetop looking like new. It replaces broken or damaged cooktop glass on compatible GE range units. What it does:

• Provides a durable, single-piece glass surface for the rangetop
• Replaces cracked, chipped, or shattered cooktop glass that can allow debris into internal components
• Restores a flat, even surface for burner trims and grates to sit correctly
• Helps prevent heat and moisture damage to underlying parts when intact

• One range top glass assembly

• Disconnect power (and gas, if applicable) before beginning; follow all safety precautions when working with glass
• Handle the glass carefully and use appropriate gloves to avoid cuts
• Installation typically requires removing burner grates, burner caps, and trim pieces to lift out the damaged glass and set the new assembly
• Verify proper fit, orientation, and seal before reassembling burners and restoring power

This lower oven warming element heats the oven's warming/holding compartment so food stays warm until serving. Replaces a damaged or non-heating lower element to restore consistent low-temperature operation. What it does:

• Heats the oven's warming/lower compartment for holding cooked food
• Replaces elements that show visible damage, burn-through, or no heat output
• Helps restore even low-temperature performance when the warmer function fails
• Works with the oven's temperature control and safety circuits to provide steady heat

• One lower oven warming element

• Disconnect power at the breaker before beginning any repair
• Wear gloves; element edges and terminals may be sharp
• Verify proper wiring and secure terminal connections during installation

This rubber rangetop bumper cushions and supports the cooktop, reducing vibration and protecting the surface from metal-on-metal contact. It helps restore proper spacing and reduces rattling or chafing from loose or missing bumpers. What it does:

• Cushions the cooktop edge to prevent scratching and wear
• Keeps the cooktop and rangetop components properly spaced and stable
• Reduces rattling, vibration, and noise during use
• Commonly replaced when bumpers are cracked, flattened, missing, or allow movement

• Remove power to the appliance and allow all surfaces to cool before servicing.
• Access may require lifting or removing the cooktop; follow manufacturer instructions for your model.
• Replace with the same style bumper to maintain proper fit and spacing.
• Use care around sharp edges.