Parts for Ge PHS930FL3DS: Cooktop Parts

This induction assembly replaces a damaged or nonworking induction surface element to restore induction heating on compatible cooktops. It provides the core induction coil and mounting needed for the element to generate heat for cookware. What it does:

• Houses the induction coil and associated hardware that create the electromagnetic field for induction cooking
• Restores heating when an induction zone fails to power or produce heat
• Resolves symptoms like no-heat, intermittent heating, or an induction zone that won't activate
• Works with the cooktop's control electronics to deliver localized heating to compatible cookware

• Disconnect power to the appliance at the breaker before servicing
• Handle the glass/ceramic surface carefully to avoid cracks or chips
• Reuse any verified mounting hardware; replace damaged fasteners as needed

Generator board assembly that produces the high-voltage spark used to ignite gas burners on compatible ranges and cooktops, helping restore reliable ignition and reduce continuous clicking or no-spark conditions. What it does:

• Generates the spark that lights surface burners and/or the oven burner on gas cooktops and ranges.
• Can stop or reduce continuous clicking with no ignition when the module fails.
• May cause one or more burners to stop sparking or ignite intermittently.
• Works with the range's ignition switches and electrode wires to coordinate safe ignition.

• Disconnect electrical power and shut off the gas supply before starting any work.
• Photograph or label wire locations before disconnecting to ensure correct reconnection.
• Handle the board and connector pins carefully to avoid damage; avoid touching components with bare hands or tools.

This 250V, 20A line fuse safeguards the appliance's power circuit by interrupting current during an overload or short. Replacing a blown fuse can restore power once the root cause is corrected.

• Opens the circuit if current exceeds 20 amps or a short occurs
• Helps protect internal wiring and control components from damage
• Typical blown-fuse symptoms: no power, dead display, won't start
• Restores line continuity after the underlying issue is resolved

• Disconnect power at the breaker/unplug before servicing
• Replace only with the same rating (250V, 20A); never bypass or upsize the fuse
• If a new fuse blows again, stop and diagnose the underlying fault before further replacement

This maintop glass is a replacement cooktop surface that restores a flat, even finish and protects internal components. It provides a clean look and lets burners and controls mount securely. What it does:

• Replaces cracked, chipped, or heavily scratched maintop glass to restore appearance and function
• Forms the cooktop surface that supports burners, grates, and control hardware
• Helps prevent spills and debris from falling into the range cabinet and control area
• Maintains proper alignment for burner assemblies and trim pieces

• Disconnect power (and gas if applicable) before starting any repair
• Handle carefully and wear cut-resistant gloves; glass can break or chip during removal/installation
• May require removal of burners, grates, knobs and mounting screws to access and replace the glass
• Verify any trim, clips, or fasteners required for installation

This lower oven warming element heats the oven's warming/holding compartment so food stays warm until serving. Replaces a damaged or non-heating lower element to restore consistent low-temperature operation. What it does:

• Heats the oven's warming/lower compartment for holding cooked food
• Replaces elements that show visible damage, burn-through, or no heat output
• Helps restore even low-temperature performance when the warmer function fails
• Works with the oven's temperature control and safety circuits to provide steady heat

• One lower oven warming element

• Disconnect power at the breaker before beginning any repair
• Wear gloves; element edges and terminals may be sharp
• Verify proper wiring and secure terminal connections during installation

The Element Induction is an OEM component specifically designed for GE electric ranges. This element measuring 3700W is responsible for generating heat through electromagnetic induction when current is passed through its coils. 

Causes of a bad induction element can include cracks or breaks in the coils over time, damage or wear to insulation allowing shorts, or malfunctions in electronic components controlling current flow. 

Symptoms of a bad element include:

• Inability to heat or boil water fully 
• Uneven or insufficient heating from the burner or cooktop surface
• Burn marks or scorching on pots and pans
• Electric circuit breakers tripping excessively

This OEM GE replacement element is also compatible with Hotpoint, RCA, and some Kenmore models. 

The Rear Vent Trim and Gasket Assembly is an OEM part for GE ranges. It seals the rear vent opening of the range, directing hot air and potential gas fumes outside through the exhaust vent during oven use. Without an intact seal provided by the gasket and vent trim, combustion byproducts can enter the kitchen presenting safety and performance issues.

Causes of a bad range rear vent assembly include wear over years of use with high heat cycles, cracking or degradation of sealing materials, or damage from cleaning or impacts around the vent area.

Symptoms of an issue include:

• Foul odors detected in the kitchen during use of the oven
• Inefficient or uneven baking and broiling
• Visible openings or gaps seen around the rear vent perimeter
• Detached, cracked, or missing components

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.