Parts for Ge JS760DP2BB: Cooling Fan Parts

The Cooling Fan Assembly is an OEM part for GE ovens, essential for maintaining optimal temperature by circulating air. It activates at a set temperature to dissipate heat efficiently, safeguarding sensitive parts. With time, it may wear out due to debris, mechanical, or electrical issues, potentially causing overheating.

Causes of a faulty Cooling Fan Assembly can vary. Mechanical wear from prolonged use can reduce efficiency or cause failure. Electrical issues like faulty wiring can impact fan operation. Dust buildup can block fan blades, affecting performance.

Symptoms indicating the need for a replacement Cooling Fan Assembly include:

• Unusual noises during operation, which may suggest a problem with the fan's motor or blades.
• Overheating of the oven's exterior or control panel, a sign that the fan isn't effectively dissipating heat.
• Error messages or codes displayed on the oven, indicating a cooling system malfunction.
• The oven shutting off unexpectedly, possibly as a safety measure due to inadequate cooling.

This OEM GE  part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is a replacement M4 hex nut used to secure small appliance panels, brackets, and assemblies. It provides a simple, reliable fastening point to restore proper fit and reduce rattles or loose parts. What it does:

• Secures panels, brackets, fasteners and small components in appliances
• Replaces missing or damaged nuts that allow parts to shift or rattle
• Restores proper thread engagement for M4-0.7 machine screws
• Helps maintain alignment of mounted assemblies when tightened correctly

• Turn off and unplug the appliance and remove power source before starting work
• Hand-start the nut to avoid cross-threading, then tighten snugly with the correct wrench; do not overtighten
• Replace any fasteners with damaged threads or stripped heads for a secure repair

A safety thermostat that stops the heater when internal temperatures get too high to protect the appliance and prevent overheating. Replaces a worn or failed high-limit switch to restore normal heater safety control. What it does:

• Monitors internal heat and opens the circuit if temperatures exceed safe limits
• Prevents continuous heating and reduces risk of overheating or fire
• Common symptom: dryer or oven heats erratically, overheats, or stops heating unexpectedly
• Works as a non-resettable safety cut-out in the appliance's vent or burner circuit

• Disconnect power (unplug appliance or switch off breaker) before servicing
• Handle terminals carefully; replace any damaged connectors and secure spade terminals fully

This vertical brace supports the refrigerator cabinet/frame to keep the right side aligned and stable, helping doors close properly and preventing cabinet sag over time. What it does

• Reinforces the refrigerator's right-side frame to maintain proper door alignment and gap
• Helps prevent cabinet sag and reduces stress on hinges and seals
• Restores structural support after impact or corrosion-related weakening
• Works with existing mounting points to transfer weight and keep panels flush

• Disconnect power before starting and work with an empty cabinet for easier access
• Typical installation uses basic hand tools; align brace before tightening fasteners
• Inspect adjacent fasteners and brackets during install; replace any damaged hardware
• Your model's service manual or diagram for exact mounting locations and torque specs

This Rear Trim Support secures the refrigerator's rear top trim, restoring a flush exterior and preventing rattles or gaps. It replaces a cracked or missing support to keep the trim panel aligned and stable. What it does:

• Holds the rear/top trim panel in place to maintain a clean exterior fit.
• Prevents trim panel movement, sagging, or vibration noise.
• Restores proper alignment after impact or long-term wear.
• Helps keep moisture and debris out of the cabinet gap around the trim.

• Disconnect power to the appliance before starting any repair.
• Basic hand tools required; handle trim pieces carefully to avoid scratches.
• Inspect adjacent clips and screws; replace any damaged fasteners for a secure fit.

The Cooling Fan Sensor is an OEM replacement part for GE ovens and ranges. It is a critical component that monitors and regulates the operation of the cooling fan, ensuring proper ventilation and temperature control within the appliance.

Symptoms of a bad cooling fan sensor:

• Overheating issues, with the oven or range becoming excessively hot
• Failure of the cooling fan to turn on or operate correctly
• Error codes or warning lights related to temperature or ventilation problems
• Potential safety hazards due to inadequate cooling and heat buildup

Causes of a faulty cooling fan sensor can include exposure to high temperatures over time, electrical malfunctions, or physical damage to the sensor or its wiring.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore ovens and ranges.