Parts for Ge PS950SF2SS: Cooling Fan Parts

The Blower Assembly is an OEM component specifically designed for GE electric ranges. Located within the oven compartment, this assembly incorporates the convection fan motor to circulate heated air throughout the cavity during baking and roasting.

Causes of blower issues typically involve degradation or failure of the dual electric motors from years of repetitive usage. Physical obstructions blocking fan operation could also cause problems. 

Symptoms include:  

• Improper or inconsistent cooking due to inefficient airflow
• Abnormally loud noises originating from the blower area
• Excessive residual heat building up in the oven cavity

This genuine GE blower assembly is compatible with Hotpoint, RCA, and select Kenmore models as well.

Fix unresponsive buttons or blank displays with this range control panel. Restores touchpad functionality and electronic controls. Moderate difficulty repair.

Replace a cracked or damaged control panel enclosure on your range. This housing protects internal electronics and restores the appearance of your unit.

This chassis brace is a right-side cabinet support that stabilizes the appliance frame and helps keep panels aligned for reliable operation and a secure fit. It restores proper cabinet support after damage or wear. What it does:

• Provides structural support to the appliance cabinet on the right side
• Helps keep exterior panels and controls aligned to reduce vibration and rubbing
• Restores correct spacing for components mounted to the chassis
• Commonly replaced when bent, cracked or after collision damage

• One right-side chassis brace

• Designed for straightforward replacement; refer to your model's service manual for exact steps
• Disconnect power (and gas if applicable) before beginning any repair
• Use proper fasteners and torque per OEM instructions; avoid overtightening
• If cabinet damage is extensive, inspect surrounding components for additional repairs

This chassis brace is a service replacement support bracket that helps keep the appliance chassis and front assembly aligned for reliable operation and reduced vibration. It restores proper fit and support where the original brace is bent, cracked, or missing. What it does:

• Provides structural support to the appliance chassis and front assembly
• Helps correct misalignment, sagging, or gaps in the front panel area
• Reduces vibration and rattling caused by a damaged or loose chassis brace
• Maintains proper spacing for controls and door components to operate smoothly

• One chassis brace

• Disconnect power to the appliance before beginning any repair
• Remove exterior panels or trim as needed to access the mounting area
• Install using original mounting holes and hardware; replace any damaged fasteners
• Do not overtighten screws; check alignment and operation after installation

This bimetal limit switch is a temperature-controlled defrost thermostat that helps stop the defrost heater once the evaporator reaches the proper temperature, protecting the system and supporting reliable defrost cycles. What it does:

• Opens and stops the defrost heater when the evaporator reaches the cut-out temperature
• Closes to allow the heater to run during defrost when temperature falls below the cut-in point
• Helps prevent excessive heating and ice buildup on the evaporator
• Commonly replaced when a unit fails to defrost, has persistent frost buildup, or shows erratic defrost cycles

• One bimetal limit switch

• Disconnect power to the appliance before attempting any repair
• Typically mounted near the evaporator or defrost heater; handle with care to avoid bending terminals
• Test with a multimeter for continuity to confirm failure before replacing

This bimetal limit thermostat helps prevent oven overheating by cutting power when internal temperatures exceed safe levels. It restores normal temperature control and protects oven components from heat damage. What it does:

• Senses excessive oven temperature and opens the circuit to stop heating
• Helps prevent continuous heating or unsafe temperature rise
• Can be replaced if oven cycles erratically, won't reach or maintain set temperature, or overheats
• Works as a safety cutoff in the oven's temperature control system

• One bimetal limit thermostat

• Disconnect power to the appliance before inspecting or replacing the part
• Follow the oven's service manual for proper access and wiring procedures
• Handle terminals and wiring carefully; ensure secure connections and correct orientation

This replacement mounting screw is used in cooking appliances to fasten components securely. It restores a tight, rattle-free fit so panels, brackets, or burner-related parts stay properly aligned during everyday use.

• Secures appliance components to the chassis or assembly
• Replaces a missing, stripped, or corroded screw
• Helps resolve loose panels, wobbling parts, or vibration noises
• Supports proper alignment of mounted parts

• Disconnect power at the breaker; for gas units, also shut off gas supply
• Allow the appliance to cool completely before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Tighten snugly without overtightening; replace damaged threads or hardware as needed

Nickel

Mounting screw secures range components and panels. Replace if screw is stripped, missing, or damaged during appliance repair or maintenance work.