Parts for Mtd 952Z490-SUA: Cylinder Head Parts

This valve kit is a genuine MTD part, sold individually. This valve kit can be used as a replacement part for a snowblower. The valve kit comes with all of the components necessary to replace the valves of a snowblower. The valve kit comes with a metal needle, a spring clip, and a plastic seal. The valves on a snowblower provide a safe passageway for the fuel to reach the carburetor.Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement.This is an OEM part sourced directly from the manufacturer. It is sold individually. This valve kit is compatible with the following outdoor appliance brands: MTD, Troy-Bilt, Craftsman, Cub Cadet, Yard Machines, Huskee, and Yard Man.

This replacement part is a push rod kit. It is a genuine replacement part made by MTD. Push rods are usually found in different types of lawnmowers. These long rods are responsible for pressing open the cylinder valves within the engine A new push rod kit might be needed if the performance of the engine is off. This can mean that the rods are damaged in some way that is affecting the motion and therefore not opening the cylinder valves. Be sure the engine is completely powered off before attempting this repair. The user should also wear working gloves to prevent injury while working close to the engine. This push rod kit is sold individually and is a genuine OEM replacement part. This part is sourced directly from the manufacturer to ensure proper fit and performance.

This is a small engine spark plug positioned in the engine cylinder head. It supplies the spark that will ignite the air-fuel mixture to enable an engine to produce power. This particular spark plug is designed with superior corrosion resistance and dependable performance. Small but mighty, this component allows for increased conductivity and heat control. If the spark plug is damaged or in poor condition, many problems may arise in equipment, including sudden stop while running, overheating, and excessive gas consumption. Replace the spark plug by disconnecting the spark plug wire first, then use a socket driver or wrench to remove the spark plug. Install the new spark plug by turning it by hand initially to avoid cross-threading. If it doesn't twist anymore, use a deep socket wrench or socket driver to tighten the plug until snug. The spark plug can also be used to tune up outdoor power equipment or improve a small engine. This part is recommended to be replaced once per season. This part works with lawn mowers, snowblowers, tillers, leaf blowers, log splitters, wood chippers, and others with small engines. It is compatible with brands such as Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, and MasterCut. This is a genuine OEM part directly from the manufacturer and is sold individually.

This replacement part is an intake valve seal. It is a genuine replacement part made by MTD. This intake valve seal is able to close the valve in the machine or appliance so that air of fuel cannot escape during use. This part is essential to the overall operation of the machine. A new intake valve seal might be needed if the current one is allowing for air or fuel to escape during use. This can cause additional problems within the machine in general. Be sure the engine is completely powered off and cooled down before attempting to replace this part. Reference the appropriate user manual for more information. This is a genuine OEM replacement part. This intake valve seal is sold individually and is sourced directly from the manufacturer to ensure a proper fit and long-lasting use.

This valve spring retainer is a genuine OEM replacement part that is designed for use with select snowblowers and snow throwers. The valve spring retainer is responsible for holding the valve spring in place, which then controls the valvetrain. The retainer secures the spring so that it can provide the right amount of pressure to ensure that the system can operate without valve b, which can damage the engine or cause faulty operation. If the valve spring retainer fails or is damaged, which can happen with regular use over time, it will need to be replaced to ensure the spring remains in place during the operation of the machine. The retainer is a metal collar-type piece and although it is durable, it could wear out or break due to several different potential situations. Regardless of the cause, a replacement must be made with an OEM part like this. This genuine part is manufactured to specific OEM standards by MTD, and is compatible with more than 150 units from MTD, Yard Machines, Yard Man, Troy-Bilt, Husky, and Cub Cadet. It is sold individually. Be sure to wear gloves and allow the unit to cool completely before performing any type of repairs.

This part is a replacement valve spring. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a defective or broken valve spring in a variety of snow blower models. Valve springs are essential to the proper functionality of the snow blower, as they enable different components to move seamlessly. Springs are subject to wear and tear, which may include stretching, corroding, or snapping. If they are rendered ineffective, they will need to be replaced with a genuine OEM part. When working on or near an engine, it's important to ensure that the equipment is powered off and completely cool before beginning any repairs. For more accurate information on how and where to place this valve spring, the appropriate owner's manual and equipment diagrams should be referred to. As an authentic replacement part, this valve spring is suitable for use on line trimmers manufactured by MTD, Craftsman, Troy-Bilt, and other brands. Please note that this is a genuine part made of high-quality, durable metal and is sold individually.

This is a replacement ex. valve spring retainer for use with snow blowers, lawnmowers, and log splitters. The function of a valve retainer is to fit on top of a valve spring and to keep it in place. This seal ensures that there is no oil leaking into the combustion chamber of the engine. Signs that the valve could be bad or going bad include misfiring, ticking sounds, and compression loss.The metal retainers are built to last, but they could fail over time. They could crack or break, which would affect the performance of the machine. This could eventually cause damage to the engine if it is not replaced.The ex. valve spring retainer This is compatible with a range of models of yard equipment from MTD, Yard Machines, Troy-Bilt, Yard-Man, Cub Cadet, and Husky. This is a genuine OEM replacement part that has been sourced from the manufacturer. It is sold individually.

This genuine MTD replacement part is a rocker arm for use with snowblowers, lawn tractors, and other equipment with an engine. A properly functioning rocker arm is essential for the safe and reliable use of the equipment. The rocker arm works to open the intake and exhaust valves. The rocker arm may become worn out or damaged with extended use, necessitating replacement. Remember to check the rocker arm periodically to spot any wear or damage. This part is an identical replacement for a rocker arm that is missing, worn out, or damaged. Prior to working with this part, please refer to the original product manual for a full list of included parts and installation instructions. A wrench set may be required for installation of this part. For safety, always wear gloves and ensure unit is powered down and cool prior to performing any installation or repair.This high quality OEM replacement part is sourced directly from the manufacturer, and it is sold individually. It is made of high-quality durable metal. This part is compatible with a variety of MTD, Yard Machines, Troy-Bilt, Yard Man, Cub Cadet, Husky, and other equipment. Please note: original part numbers 1843974, 751-11966 is now obsolete, and manufacturer has replaced the original part numbers with this part.

This is a valve adjusting nut that is an integral part of many different types of lawn and garden equipment, such as lawnmowers, trimmers, and snowblowers. The location of the part will vary based on the model. Users can refer to the equipment's diagram to determine where the component is located. The nut acts as a fastener and is made of durable metal. However, it can be damaged, may break, or become lost and will need to be replaced.If the valve adjusting nut is damaged or missing, it will need to be replaced. A pair of work gloves and basic tools will be needed for the process. Take the lawn and garden equipment and place it on a level surface before removing the spark plug wire. Access the location of the nut and remove it before installing the new replacement part.This is a genuine OEM replacement part that is directly sourced from the manufacturer. The valve adjusting nut is sold as an individual item. The part is made to be compatible with snowblowers, lawnmowers, string trimmers, leaf blowers, edgers, log splitters, wood chippers, and tillers manufactured by MTD, Troy-Bilt, Yard Machines, Craftsman, Cub Cadet, Huskee, MasterCut, and Yard-Man.