Parts for Ge APER70LWQ2: Dehumidifier Parts

This water bucket assembly collects condensate from your dehumidifier and slides in securely to engage the bucket switch. Replacing a cracked or worn bucket restores safe water collection and lets the unit operate as designed.

• Holds condensed water removed from the air during operation
• Seats to engage the bucket-present/full switch so the unit can run
• Replace if the bucket is cracked, leaking, warped, or the handle is damaged
• May help resolve "bucket full/bucket missing" messages, the unit not running, or water on the floor

• Unplug the dehumidifier and wear gloves
• Remove and empty the old bucket; clean the bucket well and drain area
• Slide the new bucket in until fully seated and aligned with the switch/float
• Restore power and confirm proper operation and no leaks

This water-level float helps detect the appliance tub's water height and prevents overfilling. Replace a failed or stuck float to restore proper fill control and reduce the risk of leaks or overflow. What it does:

• Senses water level in the tub/reservoir and works with the fill/float switch to stop filling at the correct height.
• Can cause overfilling, continuous fill, or water under the appliance when cracked, stuck, or damaged.
• Restoring a functioning float helps re-enable normal fill cycles and prevents flooding-related damage.
• Simple mechanical part — does not contain electronic controls.

• Disconnect power and shut off the water supply before starting any repair.
• Access varies by model; remove the lower access panel or kick plate to reach the float area. Keep panels and fasteners for reassembly.
• Inspect the float for debris, cracks, or binding and test free movement before replacing the switch or other components.
• After installation, restore power and run a short fill cycle to check for leaks.

This water filter assembly replaces the refrigerator's inline/replaceable water filter to help reduce taste and odor issues and deliver cleaner-tasting drinking and ice water. Designed to fit compatible GE refrigerators and install in the designated filter housing. What it does:

• Filters impurities that can cause bad taste or odor in drinking water and ice
• Helps reduce visible particles that appear in dispensed water
• Restores normal water flow when a clogged/expired filter is causing slow dispensing
• Works as the factory replacement for the refrigerator filter housing and flow path

• Turn off the water supply and relieve water system pressure before replacing the filter
• Follow the refrigerator manufacturer's access/removal steps for the filter housing
• Run and discard several glasses of water after installation to flush the system
• Replace at manufacturer-recommended intervals and dispose of the old filter per local regulations

This castor roller replaces a worn wheel that helps an appliance roll or pivot smoothly, restoring easy movement and stable positioning. Ideal when a machine drags, shifts, or doesn't glide as it should. What it does

• Provides a smooth rolling surface so the appliance moves without binding or scraping
• Supports cabinet or appliance weight at the mounting point to maintain level operation
• Reduces noise and floor damage caused by a worn or seized wheel
• Common symptom: appliance is hard to slide, tilts, or shifts unexpectedly during use

• Turn off and unplug the appliance before inspecting or replacing castors
• Support the appliance securely to prevent tipping while accessing the caster mount
• Remove mounting fasteners, swap the old caster for the replacement, and tighten hardware to the original torque

This water bucket assembly collects condensate from your dehumidifier and slides in securely to engage the bucket switch. Replacing a cracked or worn bucket restores safe water collection and lets the unit operate as designed.

• Holds condensed water removed from the air during operation
• Seats to engage the bucket-present/full switch so the unit can run
• Replace if the bucket is cracked, leaking, warped, or the handle is damaged
• May help resolve "bucket full/bucket missing" messages, the unit not running, or water on the floor

• Unplug the dehumidifier and wear gloves
• Remove and empty the old bucket; clean the bucket well and drain area
• Slide the new bucket in until fully seated and aligned with the switch/float
• Restore power and confirm proper operation and no leaks