Parts for Whirlpool WRT779REYW01: 08 - Dispenser Front Parts

This replacement drip tray catches and channels water and condensation away from the appliance interior to help reduce leaks and maintain a cleaner cabinet. Made to match the original fit and finish for easy swap-out. What it does:

• Collects meltwater and condensation from the evaporator/defrost area to prevent pooling inside the cabinet
• Directs water to the drain area so it safely evaporates or drains away
• Helps reduce odors and ice buildup by keeping the drain area contained
• Fits into the original tray location and aligns with existing drain passages

• One black drip tray (1 piece)

• Remove power to the appliance before beginning any work to avoid electrical hazards
• Access may require removing shelves, drawers, or an interior panel depending on model
• Align tray with existing slots or tabs and slide into place until it seats fully
• Inspect drain passage for debris and clean before installing the new tray

Replacement drip tray in white that installs under the appliance to collect spills and direct water away from internal components, helping prevent damage and making cleanup easier. What it does:

• Catches leaks, drips and overflow to protect the cabinet and floor.
• Directs water away from controls and electrical components to reduce risk of damage.
• Replaces cracked, warped or discolored trays that no longer hold water.
• Helps limit staining and makes routine cleanup faster.

• Disconnect power to the appliance before starting any work.
• Access the tray by removing the lower access panel or kickplate as required for your model.
• Remove the old tray and slide or snap the replacement into place; avoid forcing parts.

This drip tray in a Midnight finish sits at the dispenser area to catch minor drips and splashes, helping keep your door clean and dry. It also refreshes appearance if the original tray is cracked, stained, or missing.

• Collects drips under the dispenser to help prevent water from running down the door or onto the floor
• Provides a stable landing for cups and glasses during dispensing
• Restores a clean look if the old tray is worn or discolored
• Typical symptoms: puddling at the dispenser, mineral buildup, or a loose/warped tray

• Pull the old tray straight out; some models require lifting the front edge first
• Clean the recess thoroughly before installing the new tray
• Align tabs and press evenly until fully seated—do not force
• Avoid activating the dispenser during installation; wipe with mild soap and water only

This separator is a molded plastic divider that helps keep ice organized inside the ice bin for smoother dispensing and less clumping. It restores proper spacing so ice moves freely during dispense cycles. What it does:

• Divides and guides ice inside the ice bin to reduce jamming and clumping
• Helps improve ice feed into the auger or dispenser chute
• Reduces shifting and rattling of ice during door movement
• Restores intended bin geometry after a cracked or missing divider

• One separator

• Unplug the refrigerator or shut off power before working on the ice bin or dispenser
• Empty the ice bin and remove any loose ice to avoid spills during replacement
• Snap the separator into the molded slots in the ice bin; no tools typically required

The Dispenser Actuator is an OEM replacement part for Whirlpool refrigerators. It is a component that facilitates the dispensing of water and ice from the refrigerator's dispenser. The actuator is responsible for detecting when a glass or container is pressed against the dispenser paddle or lever, triggering the release of water or ice.

Symptoms of a bad Dispenser Actuator include:

• Refrigerator not dispensing water or ice when the paddle is pressed
• Water or ice dispensing continuously or without activation
• Difficulty in activating the dispenser or requiring excessive force
• Leaks or drips from the dispenser area

Causes of a bad dispenser actuator can include mechanical wear and tear over time, physical damage from impact or mishandling, or failure of internal components such as switches or sensors. Exposure to moisture or debris buildup can also contribute to its malfunction.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerator models. 

This replacement pad dampens vibration and cushions the appliance to reduce noise and wear. It's a simple, durable rubber/foam part that helps stabilize components and protect surfaces during operation. What it does:

• Absorbs vibration and reduces operational noise
• Prevents metal-to-metal contact and limits wear on mounting points
• Helps keep the appliance stable during cycles or operation
• Commonly used where a small cushion or isolator is needed to protect surfaces

• One replacement pad

• Disconnect power (and water if applicable) before servicing the appliance
• Access and remove the old pad per your model's service instructions; replace with the new pad in the same orientation
• Use hand tools only; avoid damaging surrounding components

This dispenser trim is the exterior bezel that finishes the refrigerator dispenser opening, restoring a clean appearance and helping align the dispenser components for smooth operation. What it does:

• Covers and protects the dispenser opening from scratches and wear
• Helps position the dispenser controls and chute for reliable use
• Prevents debris from entering behind the dispenser assembly
• Commonly replaced when the bezel is cracked, chipped, or loose

• One dispenser trim piece as shown

• Disconnect power to the appliance before beginning service
• Remove any clips or screws holding the existing trim and lift the old bezel away carefully
• Align the new trim and secure with the original fasteners; avoid overtightening

This spigot body assembly routes water from the refrigerator supply to the dispenser and replaces a worn, cracked, or leaking dispenser spigot. It restores proper water flow and helps stop drips or visible leaks at the dispenser. What it does:

• Channels water from the supply line through the dispenser area for normal dispense operation.
• Provides the structural mounting for the dispenser valve and actuator components.
• Common symptoms it can address: leaking or dripping at the dispenser, visible cracks or broken spigot housing, or intermittent water flow from the dispenser.
• Works with existing dispenser valve and seals when those components are undamaged.

• Disconnect power to the appliance and shut off the water supply before starting work.
• Access may require removing the refrigerator door panel or inner dispenser bezel.
• Inspect and replace any worn O-rings or seals during reassembly to prevent leaks; tighten fasteners only to specified torque if provided by the manufacturer.