Matthew V San Antonio , TX April 19, 2015 Appliance: Maytag Dishwasher MDB7600AWB Control panel stopped working I bought the dishwasher used and the control panel never fully worked. The countdown timer was non-functional, many of the buttons were unresponsive, and "start" needed to be pressed multiple times before the dishwasher would turn on. After a few months, none of the lights worked, and all the buttons stopped responding. I first replaced the handle, since it was also broken (the door was difficult to open) and there was a chance it wasn't registering the door as fully closed. The new handle works great, but it didn't help the control panel. Finally replaced the control panel and noted there was a black dot in the old control panel ribbon cable where the traces were broken. The new control attached easily and functions 100%. This maintenance required a torx bit (T20 I think) for the door panel, and a 1/4" socket for the computer housing and control panel. The only tricky part was unplugging the ribbon cable. The socket on the computer board has to be pulled/slid back away from the ribbon cable. This loosens the socket, so the cable can be removed. Once you insert the new cable, slide the socket towards the cable, and it should hold the cable firmly. Read More... 12 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Nut Drivers, Screwdrivers, Socket Set
Henry C Apex , NC March 14, 2015 Appliance: Model MAYTAG DISHWASHER MDB7600AWS Replace broken latch and control panel (plastic broken at handle location) Your video on replacing the broken latch and handle was great! I watched other videos using other didhwasher models to get a sense on how easy/difficult it would be to replace the control panel. Replacing the control panel on my particular dishwasher model became straight forward. The control panel used 4 hex screws to secure it to the door. The circuit board housing unit used 2 more hex screws to secure it to the control panel and door. Another hex screw secured the top of the circuit board housing unit to get inside to attach the new control panel ribbon to circuit board. Everything was easy to reassemble if you take your time. Read More... 6 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Nut Drivers, Screwdrivers
Dallas B Fayetteville , NY October 30, 2014 Appliance: Maytag Undercounter Dishwasher MDB8601AWW41 Broken latch and unable to start cycle Replaced both the latch and the control panel. The new control panel activated features not in the original unit. The new panel has a digital readout of time remaining in cycle. It allows more flexibility in delayed start. The rinse only cycle is shorter (the old rinse cycle was as long as a wash). I am not only satisfied but over joyed at the success of this 'replacement' part. Read More... 3 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Nut Drivers, Screwdrivers
Olson I Yakima , WA October 11, 2015 Appliance: Model ABD7600AWW Wouldn't start Replaced control board and complete panel Read More... 1 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Nut Drivers, Screwdrivers
Gregory N Pasadena , CA November 28, 2014 Start button on dishwasher was dead Ordered a replacement control panel. Door panel was easy to remove with a Torx screwdriver bit; a few more screws inside needed to be removed with a hex driver. Pull the ribbon cable from the control box. Install the new panel, reversing how you removed the dead panel. Reinstall all the screws. Done. Read More... 1 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Screwdrivers
James B Dublin , GA July 09, 2017 Appliance: Model MAYTAG 300 SERIES Panel where the handle attached was broken I removed the inner door cover, removed the screws holding the panel, disconnected the door switches and removed the door latch assembly. I removed the screws holding the panel in place and replaced the panel. Put everything back together, and started the dishwasher. Read More... Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Nut Drivers, Screwdrivers
Rick I Cherry Hill , NJ August 06, 2016 Appliance: Maytag Dishwasher MDB8600AWB Error code 9 Replaced front control panel Read More... Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Nut Drivers, Screwdrivers
Guy L Grafton , MA September 04, 2015 Appliance: Model MDQ7600AWQ Erratic behavior of control buttons unit wouldn't go into wash mode Push buttons are membrane-type. The wiring inside the membrane corrodes over time (and heat and moisture) until it just doesn't work at all. The membrane is integrated with the top plastic panel - not separately replaceable. Replaced the control panel that's on the top of the door. Easy to fix! Only gotcha is that you have to take off the cover of the control box (inside the door) and slide the locking bar out on the connector for the ribbon cable - the cable doesn't just push in, you have to release/relock that locking bar. Remember to get a new vent seal and install it into the new control panel, or this repair won't last long! Read More... Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Nut Drivers
Janet S Pleasant Prairie , WI August 25, 2015 The handle broke from the lath on the dishwasher Ordered the parts from Appliance Parts Pros, watched the video of the repair. Parts arrived the next day and was repaired in 30 minutes. Couldn't have gone smoother. Read More... Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Nut Drivers, Screwdrivers
Joel K Chesterfield , MO June 15, 2015 Appliance: Maytag Dishwasher MDB7600AWB Dishwasher door latch was broken and most "buttons" and lights on touch pad weren't working Replaced door latch and touch pad unit Read More... Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Nut Drivers, Screwdrivers