Martin M Hudson , OH February 23, 2015 Appliance: Jenn-Air Freestanding-Double Oven-Dual Fuel JDR8895AAS Error code 1d11 " bake" flashing indicating runaway temperature top oven not toasting properly and shutting off Oven Manual said to check oven temperature sensor ohm resistance, which checked out fine, which led me to the expensive electronic control board replacement, which I did, and that did not solve the problem. So i reviewed the oven temperature sensor again, and I read one of the Appliance Parts Pro (APP) reviews...and another customer had the same issue as I was having and replaced the oven temp sensor and fixed the problem. So thats what I did...replaced the top oven temperature and problem fixed. I also like the no hassel return on the control board...as many places don't take electronic parts back. The shipping from APP is fast...1.5 days. Reading the reviews, fast shipping and no hassle returns, will keep me coming back for these types of repairs that I can do. Thanks APP! Read More... 25 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Screwdrivers
Scott H Centennial , CO December 27, 2014 Wrong temperature readings oven wouldn't heat Replaced oven temperature sensor from inside the oven... very easy. Read More... 2 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Screwdrivers
Scott M Hooksett , NH December 17, 2015 Maytag double oven issue with upper oven not working With help from Rick on the forum I was able to locate the issue. The plug jack for the thermostat was badly melted (was located inside the insulation and melted when oven was electronically cleaned). Ordered new sensor from Appliance Parts Pro.com and had to cut the provided plug and hard wire in the harness but all worked out. Read More... 1 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Screwdrivers
Joe L The Woodlands , TX November 14, 2025 Oven not working Replaced the oven igniter and temperature sensor Read More... Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Screwdrivers
Daniel H Burnet , TX December 16, 2022 Appliance: Model WE GOT A SERVICE ESTIMATE. Temperature was not consistent and the broiler didn't work. Watched the video attached to the part number on the website and followed the instructions. Read More... Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Screwdrivers
Edward J Boise , ID January 13, 2022 Appliance: Model WGE555SOOBWO2 Oven sensor. Replaced oven sensor. Read More... Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Nut Drivers
Wes G Exeter , CA April 07, 2020 Appliance: Maytag 30`` Electric Freestanding Self Clean Range Non-Convect MGT8775XW02 Maytag double ovens off 30 50 degrees in temp Replaced oven sensor. Removed back protection plate behind stove using nut driver. Sensor was held by one nut on the right side. Replaced sensor per video. Total time 15-30 mins. Both ovens now working properly. Read More... Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Nut Drivers
Kendall C Ashland , KY December 02, 2016 Upper and lower ovens would not hold there temperature I replaced the temperature sensors in each oven. The worse part is pulling the stove away from the wall. The back comes off of the stove with eight screws and each sensor has two screws. The parts matched perfectly and the plug on each disconnected very easy. The job took about thirty minutes and a screw driver. The bottom oven temperature seems correct but the upper oven seems to be about twenty to thirty degrees to hot. Lowering the temp. setting that much seems to cure that problem. Back into baking now. Read More... Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Screwdrivers
Anthony E Chula Vista , CA November 06, 2016 Appliance: Maytag 30`` Electric Freestanding Self Clean Range Convection MGT8885XS01 Top oven was burning bottom of cookies Cookies were burning in top oven but baked fine in lower oven. Turned out to be a bad oven sensor. Read More... Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Nut Drivers
Larry H Louisville , KY September 13, 2015 Receiving error messages that the heat sensors were not working properly Ordered two new sensors - One for upper oven and one for lower oven. Replaced both. Read More... Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Screwdrivers