Parts for Bosch B22CS30SNS/02: Door 2 Parts

The Water Filter is an OEM part for Bosch refrigerators. This part removes impurities and contaminants from the water supply to your appliance. This part ensures that the water and ice dispensed by your refrigerator are clean, taste fresh, and are free of common waterborne particles and substances. 

Over time, the water filter can become clogged with sediments and contaminants, reducing its effectiveness and potentially affecting the taste and quality of the water and ice. Regular replacement is essential for maintaining optimal performance.

Symptoms of a bad Water Filter include:

• Unpleasant taste or odor in the water or ice
• Decreased water flow to the dispenser or ice maker
• Visible particulate matter in the water or ice cubes

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This replacement tray restores secure, usable storage inside your appliance. It replaces a damaged or missing tray so items are supported properly and the interior stays organized and easy to access.

• Provides a stable surface/compartment to hold items securely
• Restores organization when the original tray is cracked, warped, or missing
• Helps prevent spills and tipping from an ill-fitting or broken tray
• Common signs you need this part: visible cracks, broken tabs, loose fit, or difficulty seating the tray

• Disconnect power before servicing; if applicable, shut off water
• Remove the damaged tray and transfer any reusable inserts or hardware
• Seat the new tray fully in its guides or supports and verify a secure fit
• Do not overload immediately; check for level and stability

This door seal fits around the dishwasher tub opening to keep water and steam inside during cycles. Replacing a worn gasket restores a tight seal so the door latches properly and helps prevent leaks at the sides or bottom.

• Creates a watertight barrier between the door and tub during wash and rinse cycles
• Helps contain steam and reduce moisture escaping from the front of the unit
• Replaces a flattened, cracked, torn, or deformed seal that can cause leaks
• Common symptoms include drips at the front edge, water on the floor near the door, and needing extra force to latch

• Disconnect power and, if applicable, shut off the water supply before servicing
• Pull the old seal from the channel; clean the groove and mating surfaces thoroughly
• Press the new seal in evenly without stretching; seat corners fully and position the joint at the bottom center
• Close the door to help the seal set; a snug fit at first is normal

This support mounting bracket reinforces and secures appliance components to reduce movement and maintain proper alignment during use. It restores stable mounting for parts that have loosened, shifted, or rattled. What it does:

• Provides a stable mounting point to hold panels, assemblies, or housings in place
• Prevents vibration and noise caused by loose or sagging components
• Keeps moving parts aligned to help ensure smooth operation
• Replaces worn, cracked, or broken supports that allow parts to shift

• Intended for users comfortable disassembling appliance panels; disconnect power and water before starting
• Verify orientation and fastener locations match your appliance before tightening
• Use existing screws or fasteners unless replacement fasteners are specified by the manufacturer

A replacement hinge pivot bearing that supports the dishwasher door for smoother, quieter opening and proper alignment. Fits into the door hinge assembly to reduce binding and wear for reliable door operation. What it does

• Supports the door hinge pivot so the door opens and closes smoothly.
• Reduces friction and wear on the hinge, helping prevent sagging or misalignment.
• Stops squeaks, sticking, or rough movement caused by a worn bearing.
• Works as a direct replacement for the corresponding hinge bearing in the door assembly.

• Disconnect power to the appliance and shut off water before starting any repair.
• Support the door while removing hinge fasteners to prevent the door from dropping.
• Access typically requires removing the lower toe panel or inner door trim—use basic hand tools.
• Inspect hinge components and nearby parts for wear; replace any damaged hardware and test door alignment after installation.

This tray is a direct-replacement interior component that catches and channels water or debris so your appliance runs cleanly and reliably. It restores proper containment and support where a cracked or warped tray causes messes or leaks. What it does:

• Collects and channels water, drips, or debris away from sensitive components
• Supports internal parts or assemblies that sit on the tray
• Helps prevent leaks or water pooling that can cause odor or damage
• Common symptom: visible cracks, warping, or recurring water beneath the appliance
• Common symptom: loose or misaligned internal parts that previously rested on the tray

• One replacement tray

• High-level swap: remove access panels or racks as needed, unseat the old tray, and position the new tray until it snaps or screws into place
• Use basic hand tools; keep fasteners and any gaskets with the assembly
• Turn power and water supply off before servicing appliances where applicable

This replacement access cover restores a clean, finished appearance and protects internal components behind the appliance panel. It securely snaps or screws into place to keep wiring and parts shielded from debris. What it does

• Covers and protects internal components behind a service access or control area
• Prevents dust and debris from entering sensitive openings
• Helps stop rattling or vibration caused by a missing or damaged cover
• Restores a flush, finished look to the appliance exterior

• Disconnect power to the appliance before removing panels or working near electrical components
• Remove any retaining screws or disengage clips to access and replace the cover
• Align tabs/clips and press or fasten securely until the cover sits flush