Parts for Frigidaire FFFU20F2VW2: Door Parts

Replacement door magnet that helps the refrigerator or freezer door stay closed for a tighter seal and more consistent cooling. Restores magnetic hold so doors close reliably and reduce warm spots. What it does

• Provides magnetic hold for the door liner so the door stays shut during normal use
• Helps maintain the gasket engagement to preserve internal temperature
• Common symptom: door not staying closed, food warming, or frost build-up near the door
• Used in door/gasket assembly where magnets secure the seal

• Turn off power to the appliance or unplug before removing door trim or accessing internal components
• Remove door liner or gasket per service instructions to access and replace the magnet; keep fasteners and seals intact
• Press or seat magnet into its channel or mounting location; use the OEM fastener or adhesive method specified by the manufacturer

This precision bearing supports a rotating component inside your appliance, reducing friction for smooth, reliable operation. Replacing a worn bearing can eliminate noise and restore proper movement in the affected assembly.

• Provides low-friction support for a rotating shaft or component
• Helps maintain alignment for smooth, quiet operation
• Common symptoms include squealing/grinding noises, wobble/play, or binding/seized rotation
• Excess drag can cause overheating or motor overload

• Disconnect power and shut off gas/water supplies as applicable before service
• Match orientation to the original and your model's diagram for placement
• Clean the shaft/bore and inspect mating parts; replace worn components; apply OEM-approved lubricant only if specified
• If press-fit is required, use proper drivers/press tools; do not hammer directly on the bearing

The Refrigerator Hook-Auto Closer is an OEM part for Frigidaire French door refrigerators. Located on the top inside edges of the refrigerator doors, the hook-auto closer attaches the closing mechanism arms to allow automatic opening and closing functions. 

Symptoms of a bad hook-auto closer include: 

• Doors detached from closing mechanism  
• Linkages slipping out of place 
• Loose or unstable door movement
• Grinding noises when doors open or close

Causes of a bad hook-auto closer can be damage or deformation from excessive impact, broken weld points, or normal wear over time.

This genuine Frigidaire part is compatible with some Electrolux and Kenmore French door refrigerator models as well.

This factory screw secures interior or door components in your refrigerator so they stay tight and aligned. Replace missing, stripped, or corroded hardware to eliminate looseness and prevent parts from shifting or rattling during use.

• Fastens brackets, trim, rails, bins, or handles to the cabinet or door
• Restores a secure fit when the original screw is lost, damaged, or rusted
• Helps correct looseness, vibration, and rattling from unsecured parts
• Common symptoms: loose or wobbling handle/trim, misaligned parts, missing hardware

• Disconnect power to the appliance before servicing; turn off water if working near dispenser/ice areas
• Match to the original hardware and install in the same location; reuse any washers/spacers
• Start threads by hand to prevent cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to avoid stripping threads or cracking plastic

This replacement name plate is the identification label used on the appliance's exterior to restore a clear, readable ID and finish. It helps keep the appliance looking complete and makes model/serial information visible. What it does:

• Replaces a worn, faded, or missing identification label on the appliance exterior
• Restores the appliance's original appearance and readable markings
• Helps owners locate model/serial details when present on the label
• Prevents confusion caused by missing or damaged name plate graphics

• High-level replacement; clean and dry the mounting surface before installing for best adhesion
• Remove any old adhesive or backing carefully to avoid surface damage
• Align the label precisely, then press firmly to secure
• Disconnect power and follow basic safety precautions when removing exterior panels if required

This shelf door is a replacement door bin that restores secure storage on the refrigerator door, keeping bottles and condiments upright and organized. It's a direct-fit part designed to replace a cracked or broken door shelf. What it does:

• Holds items on the refrigerator door so bottles and containers stay upright
• Replaces cracked, warped, or broken door bins that allow items to fall or shift
• Restores proper sealing and alignment of stored items on the door
• Helps prevent spills and improves usable door storage space

• Unplug the appliance or disconnect power before beginning any repair
• Remove all items from the door and lift out the old shelf door per manufacturer instructions
• Snap or slide the new shelf door into the door rail; verify it seats evenly and securely
• If screws or fasteners are used, tighten snugly but avoid overtightening to prevent cracking

This is a replacement drum bearing that supports the dryer drum and helps it turn smoothly for reliable tumbling and even drying. It restores proper drum rotation and reduces noise caused by worn bearing surfaces. What it does:

• Supports the rear/front of the dryer drum so it spins with minimal friction
• Reduces squealing, scraping, or grinding noises from the drum area
• Prevents excessive drum wobble and uneven wear on the drum seal
• Helps restore smooth, consistent drum rotation for better drying performance

• One bearing

• Disconnect power before beginning any repair; follow all safety precautions
• Access typically requires removing the dryer top/back or front panel to reach the drum bearing
• Inspect drum rollers, glides, and seals while the dryer is opened; replace if visibly worn

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head