Parts for Bosch HMV8052U/01: Door Parts

This Outer Door Panel replaces the exterior skin of your appliance's door, restoring a clean look and proper support for the handle and trim. Ideal when the original panel is dented, scratched, or otherwise damaged.

• Forms the door's outer shell, protecting internal components and insulation
• Provides mounting points for the handle, badge, and trim pieces
• Helps maintain correct door alignment and smooth closing
• Can help with issues like visible dents/scratches, a loose or rattling panel, or damaged handle mounting holes

• Disconnect electrical power at the breaker before servicing; wear gloves to protect the finish
• Open and support the door to avoid hinge strain while removing fasteners
• Transfer handle, trim, and any nameplate or brackets from the old panel; secure the new panel with existing hardware
• Remove any protective film and verify smooth door operation

This genuine screw secures panels, brackets, and other components in your appliance. Replacing a missing, rusted, or stripped fastener restores a snug fit, reduces vibration, and helps keep assemblies properly aligned during daily use.

• Fastens panels, brackets, or covers to the appliance chassis
• Helps maintain alignment to reduce looseness and vibration
• Replaces missing, corroded, or stripped hardware

• Disconnect power and shut off water/gas before servicing
• Support the panel or component while removing the damaged screw
• Start the new screw by hand to avoid cross-threading, then tighten until snug—do not overtighten
• If the receiving clip or hole is stripped, repair or replace that hardware before reinstalling

The Hook is an OEM part for Bosch microwave doors. Manufactured from heat resistant composite materials, it firmly holds the door closed during cooking cycles.  

Causes of a faulty latch/hook include failures of being worn down from repetitive opening/closing motions over time. Exposure to high heat or abrasive cleaners also leads to decreased functionality.

Symptoms of a damaged latch/hook involve:

• Doors not sealing fully or locking properly
• Failure to open after cooking
• Degrading latch fittings allowing moisture or debris entry

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This replacement spring restores the proper tension and return action for the mechanism it serves in your appliance. It helps moving parts operate smoothly and reset reliably so doors, levers, or linkages stay aligned and feel correct. What it does:

• Provides controlled tension so doors, flaps, levers, or linkages move and return to position correctly
• Helps maintain alignment and consistent feel of the mechanism
• Typical failure signs: weak or broken return, sticking/sluggish movement, parts that won't stay in position, or unusual popping noises
• Visible distortion, rust, or a missing spring indicates replacement is needed

• Includes 1 spring

• Disconnect power (and water, if applicable) before servicing; wear gloves and eye protection
• Springs store energy—release and install with care, keeping fingers clear
• Note original routing/orientation; take photos to match placement during reassembly
• Use needle-nose pliers or a hook tool for control; replace paired springs together if your model uses two

Replacement screw for securing appliance components and panels. Use it to swap out a missing, stripped, or corroded fastener so parts stay tight and properly aligned for smooth, reliable operation.

• Fastens panels, brackets, or assemblies to the appliance frame or subassemblies
• Replaces missing, stripped, or rusted hardware
• Helps reduce vibration, rattling, and loose fits
• Supports correct alignment of mating parts during reassembly

• Disconnect power; shut off water or gas supply before service
• Match the screw to the original location and orientation
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Reuse any original washers or clips from the assembly if present

Replacement door seal that forms a watertight barrier around the dishwasher door to help prevent leaks and restore proper closure. Installs where the door meets the tub to help keep wash water inside the appliance. What it does:

• Creates a watertight seal at the door to reduce or stop water leaking during wash cycles.
• Helps the door close evenly and hold pressure so the dishwasher can run normally.
• Replaces cracked, flattened or torn seals that no longer compress properly.
• Restores the intended fit between door and tub to reduce water escape and maintain cleaning performance.

• Disconnect power and water supply before servicing; follow all safety precautions in your appliance manual.
• Remove the old gasket and clean the channel fully before installing the new seal to ensure a proper fit.
• Press the new seal evenly into the door channel, ensuring any tabs or grooves are properly seated; avoid stretching the gasket.
• After installation, run a short cycle and inspect around the door for leaks; re-seat as needed.

This door handle replaces a worn or damaged appliance door grip to restore safe, reliable opening and closing. It provides a secure hold and a finished look so the door operates properly and looks like new. What it does:

• Replaces a cracked, loose, or broken door handle to restore normal door function
• Provides a secure grip for opening and closing the appliance door
• Helps prevent further damage to the door or latch from using a compromised handle
• Matches original mounting points for a direct-fit replacement when the correct part number is used

• Disconnect power and empty the door (shelves/contents) before starting
• Use common hand tools; handle is typically secured with screws or clips—retain hardware if in good condition
• Do not overtighten fasteners to avoid cracking the handle or door

This factory support secures its mating component inside the appliance, keeping it properly positioned so things open, slide, or operate as intended. Replacing a cracked or missing support restores alignment and prevents excess movement, noise, or wear.

• Provides a stable mounting point for the associated part or assembly
• Maintains alignment to ensure smooth, consistent operation
• Helps prevent vibration, rattling, rubbing, or premature wear
• Common signs of failure: visible cracks, looseness, misalignment, dragging, or a part that won't stay in place

• Disconnect power and, if applicable, shut off water or gas before servicing
• Use your model's diagram to identify the exact location and fasteners
• Transfer any screws/clips from the original part; seat the support fully
• Verify alignment and operation before restoring power