Parts for Electrolux GCRI305CADD: Door Parts

Replaces cracked, broken, or missing trim on your range door. Restores a finished look, holds glass in place, and eliminates gaps around the door edge.

Transparent glass panel for your range oven door. Replace when cracked, broken, or clouded to restore clear viewing and proper heat insulation.

Molded protective mounting shield that covers and protects internal range components from debris and damage. Replace if cracked, broken, or missing.

This refrigerator cabinet insulation panel helps keep cold in and heat out to improve cooling consistency and efficiency. It replaces damaged or missing insulation to reduce frost, hot spots, and excess compressor run time. What it does:

• Provides thermal barrier between the cabinet and outer shell to retain cold air
• Helps reduce frost buildup and condensation inside the cabinet
• Can improve cooling performance and reduce excessive compressor cycling
• Dampens vibration and reduces operating noise

• Disconnect power and empty the appliance before beginning any repair
• Remove interior panels or shelves as needed to access the insulation; follow model-specific service instructions
• Handle insulation carefully to avoid tearing; use gloves and eye protection when trimming or repositioning
• If adhesive or clips are damaged, replace with OEM fasteners

Foam insulation panel for range cabinets. Reduces heat transfer and stabilizes internal temperatures. Replace if torn, missing, or damaged to restore efficiency.

Inner door glass panel for range and wall oven doors. Replace if cracked, shattered, or slipped out of position. Installs between outer glass and oven cavity.

Mounting screw for electric and gas ranges. Secures panels, brackets, and internal components. Replace if screw is stripped, missing, or broken.

Replace your range oven door gasket to prevent heat escape and maintain proper temperature. Snaps into place with embedded clips. Confirm fit by model.

Clear inner door glass panel for range ovens. Mounts inside the oven door assembly for viewing food while cooking. Replace if cracked, chipped, or scratched.

Factory replacement support plate for electric and gas ranges. Covers and supports internal components. Replace when bent, cracked, or missing to restore proper alignment.

This is a dual-spring door hinge that attaches the oven door to the range body. It allows the door to open and close smoothly while holding it at the desired position. Replace this hinge if the oven door is sagging, not closing evenly, feels loose, or will not stay in the open position.

Replace your range's oven door handle if it's cracked, broken, or worn. This structural component mounts to the oven door for opening and closing access.

Mounting bracket for electric and gas ranges. Secures components inside the range cabinet. Replace if bent, broken, or missing during repairs or upgrades.

Replace worn or damaged insulation for your range oven door top cap. Essential for proper door sealing and heat retention when original is cracked or missing.

This replacement door cap is the molded end cap that finishes and protects the edge of a refrigerator door, restoring a clean appearance and covering exposed hardware. It helps keep the door trim sealed and cosmetically intact. What it does

• Covers and protects the exposed door edge and hinge area from damage and wear
• Restores a finished, factory appearance when the original cap is cracked or missing
• Helps prevent dirt and moisture from collecting in the exposed trim area
• Reduces rubbing or misalignment caused by damaged door trim

• One door cap/end cap

• High-level, snap-on or screw-retained installation; follow the manufacturer's diagram for the correct orientation
• Remove the door or hinge only if required by the manufacturer's instructions
• Disconnect power to the appliance before working near electrical components or removing door-mounted controls
• Use basic hand tools and take care not to scratch painted surfaces during installation

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

Replacement mounting screw that secures panels, trim, and components in ranges and ovens. Needed when original screws are lost, stripped, or damaged.

Spacer that maintains proper gap between components in your range or oven assembly. Replace if missing, worn, or damaged to restore correct fit and alignment.

Replacement screw secures panels, trim, and internal components in your appliance. Needed when original fastener is missing, stripped, or damaged.

Size: 8-32t x 0.500 inch. Color: Black.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.