Parts for Frigidaire CGEF3055MBB: 09 - Door Parts

This Door Trim Kit replaces a damaged or missing trim piece on the appliance door, restoring a clean, finished look and proper fit. It helps keep the door's outer components in place and eliminates gaps or rattles.

• Provides a clean, finished edge around the door and covers exposed fasteners
• Helps secure exterior door trim components as designed by the manufacturer
• Replaces cracked, warped, or missing trim that can snag or look unsightly
• Common symptoms: loose or rattling trim, visible gaps around the door, or broken/missing sections

• Disconnect power before servicing; allow hot surfaces to cool
• Support the door on a padded surface; some models require door removal
• Use non-marring tools; transfer any original clips/screws/emblems as needed
• After reassembly, check door alignment and operation

This inner oven door glass assembly replaces damaged or cracked interior glass to restore a clear view into the oven cavity and help maintain proper heat containment. Designed to fit as the inner glazing panel in compatible Frigidaire oven doors. What it does:

• Replaces cracked, shattered, or fogged inner oven door glass
• Restores clear visibility to monitor cooking without opening the door
• Helps maintain oven heat containment and consistent cooking performance
• Reduces risk of injury from broken glass when the door is damaged

• One inner oven door glass assembly

• Installation may require removing the oven door and separating door panels; follow the manufacturer's service instructions
• Handle glass carefully and wear cut-resistant gloves and eye protection
• Ensure all fasteners and any gasket or trim pieces are reinstalled per OEM guidance

This flat replacement glass shelf provides a stable, easy-to-clean surface inside the refrigerator to help organize and protect food. It restores proper shelving where the original glass was cracked, scratched, or missing. What it does:

• Replaces a flat refrigerator shelf glass to support food items and containers
• Restores even storage surfaces and prevents spills from soaking shelves below
• Helps maintain refrigerator interior organization and visibility of contents
• Fits into existing shelf supports or trim rails when the original glass is damaged or removed

• One flat replacement glass shelf

• Handle the glass carefully and wear cut-resistant gloves to avoid injury
• Remove food and any trim/shelf supports before swapping the glass
• Place the new glass into the existing rails or supports; do not force or bend components
• If any clips, rails or seals are damaged, replace them before use to ensure proper fit and safety

The Screw is an OEM replacement part for Frigidaire appliances. This screw is used to securely fasten components, such as panels, brackets, or internal parts, ensuring the appliance remains stable and functions correctly. Its precise design ensures a snug fit and reliable performance in the designated area of the appliance.

Over time, screws can become stripped, corroded, or loosened due to vibrations, frequent use, or environmental factors. A damaged or missing screw may lead to instability, misaligned components, or operational issues with the appliance.

Symptoms of a bad or missing screw include:

• Loose or misaligned panels or components
• Rattling or unusual noises during operation
• Difficulty in securing parts during repairs or adjustments
• Parts becoming detached or unstable

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Oven Seal is an OEM replacement part for Frigidaire ovens. This seal is installed around the oven door to create a tight barrier, preventing heat from escaping during operation. By maintaining the internal temperature, the seal ensures efficient cooking and baking while reducing energy consumption.

Over time, the oven seal can wear out or become damaged due to exposure to high temperatures, frequent use, or accidental mishandling. A compromised seal can lead to heat loss, uneven cooking, or longer preheating times.

Symptoms of a bad oven seal include:

• Heat escaping from the oven door
• Longer cooking times or unevenly cooked food
• The oven taking longer to preheat
• Visible cracks, tears, or flattening of the seal

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This clear glass shelf provides a sturdy, easy-to-clean storage surface for your refrigerator, helping keep food organized and visible. It restores usable shelving space when an original shelf is cracked, chipped, or missing. What it does:

• Supports food containers, plates and small appliances so items stay organized and level.
• Prevents spills and crumbs from falling to lower compartments; makes clean-up quicker.
• Replaces cracked, chipped or broken shelves that can cause items to shift or fall.
• Restores a proper storage surface when the original interior shelf is damaged or removed.

• Remove food and any loose items from the shelf area before replacing the glass.
• Handle with care and wear cut-resistant gloves; support the glass from underneath while sliding into place.
• Inspect shelf supports or rails for damage and position the glass evenly on the supports; do not force the shelf into misaligned rails.
• Refer to your appliance's owner manual or service guide for model-specific placement instructions.

This factory replacement plate is used on Frigidaire-made cooking appliances to cover and support a specific area of the unit. Replacing a bent or missing plate restores proper protection, alignment, and a clean, finished appearance. What it does

• Covers an opening or shields internal components as designed for the model
• Provides a stable mounting surface for adjacent parts or hardware
• Helps prevent debris intrusion and potential rattles or vibration
• Common signs it's needed: plate is missing, bent, cracked, or won't fasten securely

• 1 plate

• Disconnect power (and gas, if applicable) and allow the appliance to cool before servicing
• Retain and reuse existing screws/fasteners unless your model specifies new hardware
• Align the plate with existing holes; start screws by hand to avoid cross-threading and tighten evenly
• Verify clearances and safe operation before restoring power

This surface burner cap fits gas ranges and cooktops. It sits atop the burner head to shape the flame and shield the burner from spills, helping restore smooth ignition and consistent, even heat output.

• Shapes and distributes the burner flame for more even cooking
• Protects the burner head from spills and debris
• Helps ensure reliable ignition and a stable, blue flame
• Common signs it's needed: missing/damaged cap, uneven or yellow flames, burner slow to light, rattling cap

What's included: One surface burner cap. Install notes:

• Turn the burner off and allow the cooktop to cool completely before servicing.
• Remove the grate and lift off the old cap; clean the burner head and ports if needed.
• Center the new cap on the matching burner head so it sits level and fully seated.
• Reinstall the grate and test; realign the cap if the flame is uneven.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

This is a replacement adhesive label used to restore legible identification or instruction markings on the appliance. Replacing a damaged or missing label helps keep model, rating and safety information readable for service and ownership. What it does

• Restores faded, torn or missing identification and rating information
• Makes model/serial and safety markings easy to read during service
• Helps ensure important usage or caution text remains visible
• Prevents further wear where original adhesive label has peeled

• One replacement adhesive label

• Install on a clean, dry surface; wipe area with isopropyl alcohol and let dry before applying
• Align carefully—adhesive is permanent and difficult to reposition once set
• Use gloves to avoid contaminating the adhesive or leaving fingerprints
• Disconnect power before working in the area

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts