Parts for Frigidaire FFFU20F4VN0: Door Parts

Replacement door magnet that helps the refrigerator or freezer door stay closed for a tighter seal and more consistent cooling. Restores magnetic hold so doors close reliably and reduce warm spots. What it does

• Provides magnetic hold for the door liner so the door stays shut during normal use
• Helps maintain the gasket engagement to preserve internal temperature
• Common symptom: door not staying closed, food warming, or frost build-up near the door
• Used in door/gasket assembly where magnets secure the seal

• Turn off power to the appliance or unplug before removing door trim or accessing internal components
• Remove door liner or gasket per service instructions to access and replace the magnet; keep fasteners and seals intact
• Press or seat magnet into its channel or mounting location; use the OEM fastener or adhesive method specified by the manufacturer

This precision bearing supports a rotating component inside your appliance, reducing friction for smooth, reliable operation. Replacing a worn bearing can eliminate noise and restore proper movement in the affected assembly.

• Provides low-friction support for a rotating shaft or component
• Helps maintain alignment for smooth, quiet operation
• Common symptoms include squealing/grinding noises, wobble/play, or binding/seized rotation
• Excess drag can cause overheating or motor overload

• Disconnect power and shut off gas/water supplies as applicable before service
• Match orientation to the original and your model's diagram for placement
• Clean the shaft/bore and inspect mating parts; replace worn components; apply OEM-approved lubricant only if specified
• If press-fit is required, use proper drivers/press tools; do not hammer directly on the bearing

This bearing supports and allows smooth rotation of the dryer drum, helping reduce noise and wear. Replacing a worn bearing restores stable drum movement and helps prevent scraping, thumping, or drag during cycles.

• Supports the rear of the drum for proper alignment and smooth rotation
• Can help address squeaking, grinding, scraping, or thumping sounds
• Reduce drum wobble, drag, or intermittent stopping during operation
• Wear item that can degrade over time with heat and load stress

• Disconnect power before service and allow components to cool
• Access typically requires removing the top and front panels
• Inspect the drum shaft, support bracket, and glides for wear; replace if needed
• Apply manufacturer-approved high-temp lubricant where specified

Color: White

The Refrigerator Hook-Auto Closer is an OEM part for Frigidaire French door refrigerators. Located on the top inside edges of the refrigerator doors, the hook-auto closer attaches the closing mechanism arms to allow automatic opening and closing functions. 

Symptoms of a bad hook-auto closer include: 

• Doors detached from closing mechanism  
• Linkages slipping out of place 
• Loose or unstable door movement
• Grinding noises when doors open or close

Causes of a bad hook-auto closer can be damage or deformation from excessive impact, broken weld points, or normal wear over time.

This genuine Frigidaire part is compatible with some Electrolux and Kenmore French door refrigerator models as well.

This factory screw secures interior or door components in your refrigerator so they stay tight and aligned. Replace missing, stripped, or corroded hardware to eliminate looseness and prevent parts from shifting or rattling during use.

• Fastens brackets, trim, rails, bins, or handles to the cabinet or door
• Restores a secure fit when the original screw is lost, damaged, or rusted
• Helps correct looseness, vibration, and rattling from unsecured parts
• Common symptoms: loose or wobbling handle/trim, misaligned parts, missing hardware

• Disconnect power to the appliance before servicing; turn off water if working near dispenser/ice areas
• Match to the original hardware and install in the same location; reuse any washers/spacers
• Start threads by hand to prevent cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to avoid stripping threads or cracking plastic

The Hook is an OEM part for Frigidaire refrigerators. It helps to ensure a secure and proper closure of the refrigerator door.

A bad door closer hook can be caused by wear and tear, damage, or misalignment. Signs of a faulty door closer hook include the door not closing fully or not staying closed, difficulty in opening or closing the door smoothly, or a loose or wobbly door.

Symptoms of a bad door closer hook can include:

• The refrigerator door not sealing properly
• Excessive force required to open or close the door
• Visible damage or misalignment of the door closer hook

Replace your worn or damaged door closer hook with this genuine OEM part to restore your refrigerator door. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The Handle is an OEM component specifically designed for Frigidaire refrigerators. This door handle is located on the exterior front of the fridge, providing an ergonomic grip for easy opening and closing of the refrigerator door. 

Symptoms of a bad handle can include loose mounting, difficulty grasping or turning the handle, or physical damage rendering it unusable. 

Causes of a bad handle include wear and tear over time, damage from impact or harsh cleaning chemicals, or loose fasteners allowing the handle to wobble.

Symptoms of a bad handle include:

• Loose, unstable grip that cannot support door weight  
• Difficulty opening and closing the refrigerator door
• Damage to the handle mechanism, mounting bracket, or appearance

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace yours today before replacing becomes necessary.
 

This glass shelf replaces a damaged or missing refrigerator shelf to restore stable storage and organization. It provides a flat, easy-to-clean surface for holding food and containers so items stay level and visible. What it does

• Replaces a broken, cracked or missing refrigerator shelf to restore usable storage space
• Provides a stable, flat surface for holding food, platters and containers
• Helps keep items organized and prevents spills from reaching lower compartments
• Easy to wipe clean for simple maintenance and hygiene

• One replacement glass shelf

• Handle glass carefully and wear cut-resistant gloves to avoid injury
• Slide into existing shelf supports or clips; no special tools typically required
• Verify shelf orientation and seating on supports before loading with items
• Do not use if glass is chipped or cracked; replace immediately to prevent breakage

This is a replacement drum bearing that supports the dryer drum and helps it turn smoothly for reliable tumbling and even drying. It restores proper drum rotation and reduces noise caused by worn bearing surfaces. What it does:

• Supports the rear/front of the dryer drum so it spins with minimal friction
• Reduces squealing, scraping, or grinding noises from the drum area
• Prevents excessive drum wobble and uneven wear on the drum seal
• Helps restore smooth, consistent drum rotation for better drying performance

• One bearing

• Disconnect power before beginning any repair; follow all safety precautions
• Access typically requires removing the dryer top/back or front panel to reach the drum bearing
• Inspect drum rollers, glides, and seals while the dryer is opened; replace if visibly worn

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

This part number contains one (1) screw.

The Door Handle Screw is an OEM part for Frigidaire refrigerators. This screw secures the door handle to the refrigerator door, ensuring a firm and stable grip for opening and closing the door.

Causes of a bad door handle screw can include regular wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or stripping. A faulty screw can lead to a loose or wobbly door handle, making it difficult to operate the refrigerator.

Symptoms of a bad door handle screw include:

• The door handle feeling loose or coming off
• Difficulty in securely tightening the handle
• Visible rust or corrosion on the screw
• Stripped threads on the screw or handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This wiring harness connects electrical components inside the appliance to restore reliable power and signal paths. Replacing a damaged harness helps eliminate intermittent operation and restores proper component communication. What it does:

• Provides secure electrical connections between internal components and the main control
• Replaces frayed, burned, or broken wiring that can cause intermittent or no operation
• Helps stop shorts or poor connections that lead to error codes or component failures
• Maintains factory routing and connector fit for correct installation and function

• One wiring harness as shown

• Disconnect power before inspecting or replacing the harness to avoid shock or damage
• Inspect mating connectors and terminals for damage; replace any corroded parts
• Test appliance function after installation and secure any loose wires or clips