Parts for Frigidaire FFHT1835VW3: Door Parts

This replacement name plate is the identification label used on the appliance's exterior to restore a clear, readable ID and finish. It helps keep the appliance looking complete and makes model/serial information visible. What it does:

• Replaces a worn, faded, or missing identification label on the appliance exterior
• Restores the appliance's original appearance and readable markings
• Helps owners locate model/serial details when present on the label
• Prevents confusion caused by missing or damaged name plate graphics

• High-level replacement; clean and dry the mounting surface before installing for best adhesion
• Remove any old adhesive or backing carefully to avoid surface damage
• Align the label precisely, then press firmly to secure
• Disconnect power and follow basic safety precautions when removing exterior panels if required

The Fresh Food Door Gasket (Gray) is an OEM replacement part for Frigidaire refrigerators. As a critical component, this gasket forms an insulating seal around the refrigerator's fresh food door opening. It helps maintain interior temperatures and energy efficiency. 

Causes of a bad gasket can include cracks or splits developing from repeated opening and closing of the door. General wear through daily use may also cause seal degradation over time. 

Symptoms of a bad door gasket include: 

• Higher than normal energy bills   
• Excess frost or moisture buildup inside  
• Difficulty closing the refrigerator door fully
• Inability to reach optimal cooling levels

This OEM Frigidaire replacement is compatible with some Electrolux, Kelvinator, and Kenmore refrigerators as well.

This replacement gasket restores a tight, flexible seal where your appliance needs it—helping contain air, moisture, or heat so performance stays consistent and leaks are minimized. Use it to replace a worn or damaged seal and improve efficiency.

• Forms a compressible seal between two mating surfaces
• Helps prevent air or water from escaping, supporting correct temperature and moisture control
• Replace if the old gasket is torn, cracked, hardened, misshapen, or won't stay seated
• Common symptoms include visible gaps, poor closure/fit, moisture at the edge, or temperature inconsistencies near the opening

• Disconnect power; turn off water supply if applicable
• Remove the old gasket and thoroughly clean the channel/mating surfaces before installing
• For door-style seals, warming the gasket (warm water or low heat) can help it relax; set corners first and seat evenly
• After installation, check for leaks or air gaps during a test run

This door shelf bin restores usable storage on the inner door. Replace a cracked, broken, or missing bin to keep items organized and help prevent spills when opening and closing the door.

• Attaches to the door liner to hold food items and containers
• Replace if the original is cracked, warped, or has broken mounting tabs
• Common symptoms: bin falls off or won't stay seated, reduced door storage, items tipping or sliding
• Restores proper fit and organization on the door

• Empty the bin and support the door while working
• Remove the old bin by lifting up and out; align the new bin with the door rails and press down until fully seated
• Do not force; ensure you're installing in the correct door position for this bin
• No electrical work required; handle plastic parts carefully to avoid cracking

This replacement refrigerator bin restores safe, organized storage space inside your appliance. It securely holds bottles, jars, and small items so they don't tip, spill, or get lost—helping you maximize capacity and keep contents easy to reach. What it does:

• Provides contained storage for food and beverages in the designated compartment
• Attaches to molded supports/rails for stable, removable organization
• Replaces cracked or broken bins to restore usable space
• Common symptoms: stress cracks, broken tabs, bin won't stay seated, items falling or spilling

• 1 bin

• Remove contents, then lift the old bin up and out from its supports
• Align the new bin on the supports; slide or press down until fully seated
• Do not force or overload; verify placement and orientation per your model
• Minimize door-open time to maintain temperature; no electrical work required

This replacement door bin restores secure, organized storage on your refrigerator door, keeping bottles and condiments in place and easy to reach. It's a direct swap for a damaged or missing bin to keep items from tipping or falling.

• Mounts on the inner door as a shelf-style bin to hold jars, bottles, and small items
• Helps organize contents and maximize usable door space
• Replace if cracked, chipped, or the retaining tabs are broken
• Common symptoms: bin falls off, won't stay seated, or the original is missing

• Empty the old bin and lift straight up to release from the door tabs/rails
• Align the new bin with the slots/rails and press down until fully seated
• Do not force cold plastic; let it warm to room temperature to reduce cracking risk
• Avoid overloading the bin after installation

This precision bearing supports a rotating component inside your appliance, reducing friction for smooth, reliable operation. Replacing a worn bearing can eliminate noise and restore proper movement in the affected assembly.

• Provides low-friction support for a rotating shaft or component
• Helps maintain alignment for smooth, quiet operation
• Common symptoms include squealing/grinding noises, wobble/play, or binding/seized rotation
• Excess drag can cause overheating or motor overload

• Disconnect power and shut off gas/water supplies as applicable before service
• Match orientation to the original and your model's diagram for placement
• Clean the shaft/bore and inspect mating parts; replace worn components; apply OEM-approved lubricant only if specified
• If press-fit is required, use proper drivers/press tools; do not hammer directly on the bearing

The Refrigerator Hook-Auto Closer is an OEM part for Frigidaire French door refrigerators. Located on the top inside edges of the refrigerator doors, the hook-auto closer attaches the closing mechanism arms to allow automatic opening and closing functions. 

Symptoms of a bad hook-auto closer include: 

• Doors detached from closing mechanism  
• Linkages slipping out of place 
• Loose or unstable door movement
• Grinding noises when doors open or close

Causes of a bad hook-auto closer can be damage or deformation from excessive impact, broken weld points, or normal wear over time.

This genuine Frigidaire part is compatible with some Electrolux and Kenmore French door refrigerator models as well.

This factory screw secures interior or door components in your refrigerator so they stay tight and aligned. Replace missing, stripped, or corroded hardware to eliminate looseness and prevent parts from shifting or rattling during use.

• Fastens brackets, trim, rails, bins, or handles to the cabinet or door
• Restores a secure fit when the original screw is lost, damaged, or rusted
• Helps correct looseness, vibration, and rattling from unsecured parts
• Common symptoms: loose or wobbling handle/trim, misaligned parts, missing hardware

• Disconnect power to the appliance before servicing; turn off water if working near dispenser/ice areas
• Match to the original hardware and install in the same location; reuse any washers/spacers
• Start threads by hand to prevent cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to avoid stripping threads or cracking plastic