Parts for Frigidaire FFHT2045VS3: Door Parts

This stainless steel freezer door kit replaces a damaged or dented freezer door to restore your freezer's appearance and help maintain a proper seal. Designed as a direct-fit replacement for compatible models. What it does:

• Replaces a scratched, dented or corroded freezer door surface
• Restores proper door alignment and helps maintain interior temperature
• Improves appliance appearance with a stainless steel finish
• Stops drafts and reduces moisture buildup caused by damaged doors

• Disconnect power to the appliance before beginning any repairs
• Installation may require removing the hinge pins and lifting the old door off; two people can help handle the door safely
• Handle and hinge hardware may need transfer from the old door
• Follow model-specific instructions and use proper tools to avoid damage

The Fresh Food Door Gasket (Gray) is an OEM replacement part for Frigidaire refrigerators. As a critical component, this gasket forms an insulating seal around the refrigerator's fresh food door opening. It helps maintain interior temperatures and energy efficiency. 

Causes of a bad gasket can include cracks or splits developing from repeated opening and closing of the door. General wear through daily use may also cause seal degradation over time. 

Symptoms of a bad door gasket include: 

• Higher than normal energy bills   
• Excess frost or moisture buildup inside  
• Difficulty closing the refrigerator door fully
• Inability to reach optimal cooling levels

This OEM Frigidaire replacement is compatible with some Electrolux, Kelvinator, and Kenmore refrigerators as well.

This replacement gasket restores a tight, flexible seal where your appliance needs it—helping contain air, moisture, or heat so performance stays consistent and leaks are minimized. Use it to replace a worn or damaged seal and improve efficiency.

• Forms a compressible seal between two mating surfaces
• Helps prevent air or water from escaping, supporting correct temperature and moisture control
• Replace if the old gasket is torn, cracked, hardened, misshapen, or won't stay seated
• Common symptoms include visible gaps, poor closure/fit, moisture at the edge, or temperature inconsistencies near the opening

• Disconnect power; turn off water supply if applicable
• Remove the old gasket and thoroughly clean the channel/mating surfaces before installing
• For door-style seals, warming the gasket (warm water or low heat) can help it relax; set corners first and seat evenly
• After installation, check for leaks or air gaps during a test run

This replacement door kit restores a damaged or worn appliance door so it closes securely and looks like new. It's an exact-fit repair part designed to return proper door function and help prevent leaks, drafts, or heat loss. What it does

• Replaces a cracked, dented, or otherwise damaged door to restore appearance and operation
• Restores proper door closing and sealing to reduce leaks, drafts, or temperature loss
• Corrects alignment issues caused by bent or worn door components
• Stops rattling or movement caused by broken or missing door parts
• Helps ensure latches and hinges engage as intended for safe use

• One door kit

• Disconnect power and/or gas and follow the appliance manufacturer's safety instructions before beginning
• Use basic hand tools; support the door during removal to avoid dropping or damage
• Inspect surrounding seals, hinges, and latch for wear and replace if needed for best results

The Door Bin is an OEM part for Frigidaire refrigerators. It is designed to securely hold and organize products on the door, keeping them easily accessible and fresh.

A bad door bin can be caused by wear and tear, damage, or improper handling. When the assembly becomes faulty, it can result in issues such as a loose or broken door bin, difficulty in opening or closing the bin, or inadequate temperature control for items.

Symptoms of a bad bin include:

• Unstable or wobbly storage for dairy products
• Difficulty in accessing or retrieving items from the bin
• Spoiled items due to temperature fluctuations

Replace your faulty bin with this genuine OEM part to restore organization in your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The Door Bin is an OEM part for Frigidaire refrigerators. It is designed to securely hold and organize products on the door, keeping them easily accessible and fresh.

A bad door bin can be caused by wear and tear, damage, or improper handling. When the assembly becomes faulty, it can result in issues such as a loose or broken door bin, difficulty in opening or closing the bin, or inadequate temperature control for items.

Symptoms of a bad bin include:

• Unstable or wobbly storage for dairy products
• Difficulty in accessing or retrieving items from the bin
• Spoiled items due to temperature fluctuations

Replace your faulty bin with this genuine OEM part to restore organization in your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This bearing supports and allows smooth rotation of the dryer drum, helping reduce noise and wear. Replacing a worn bearing restores stable drum movement and helps prevent scraping, thumping, or drag during cycles.

• Supports the rear of the drum for proper alignment and smooth rotation
• Can help address squeaking, grinding, scraping, or thumping sounds
• Reduce drum wobble, drag, or intermittent stopping during operation
• Wear item that can degrade over time with heat and load stress

• Disconnect power before service and allow components to cool
• Access typically requires removing the top and front panels
• Inspect the drum shaft, support bracket, and glides for wear; replace if needed
• Apply manufacturer-approved high-temp lubricant where specified

The Hook is an OEM part for Frigidaire refrigerators. It helps to ensure a secure and proper closure of the refrigerator door.

A bad door closer hook can be caused by wear and tear, damage, or misalignment. Signs of a faulty door closer hook include the door not closing fully or not staying closed, difficulty in opening or closing the door smoothly, or a loose or wobbly door.

Symptoms of a bad door closer hook can include:

• The refrigerator door not sealing properly
• Excessive force required to open or close the door
• Visible damage or misalignment of the door closer hook

Replace your worn or damaged door closer hook with this genuine OEM part to restore your refrigerator door. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This factory screw secures interior or door components in your refrigerator so they stay tight and aligned. Replace missing, stripped, or corroded hardware to eliminate looseness and prevent parts from shifting or rattling during use.

• Fastens brackets, trim, rails, bins, or handles to the cabinet or door
• Restores a secure fit when the original screw is lost, damaged, or rusted
• Helps correct looseness, vibration, and rattling from unsecured parts
• Common symptoms: loose or wobbling handle/trim, misaligned parts, missing hardware

• Disconnect power to the appliance before servicing; turn off water if working near dispenser/ice areas
• Match to the original hardware and install in the same location; reuse any washers/spacers
• Start threads by hand to prevent cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to avoid stripping threads or cracking plastic