Parts for Frigidaire FGF365DUC: 11 - Door Parts

Replace a damaged or worn exterior door trim to restore a refrigerator's appearance and ensure a proper edge finish. This black door trim provides a clean, factory-style look for a seamless door outline. What it does:

• Covers and protects the outer edge of the refrigerator door from chips, scratches, and wear
• Restores a straight, finished door edge to improve appearance and seal alignment
• Commonly replaced for cracked, warped, or broken trim after impact or long-term wear
• Helps maintain proper door clearance by keeping the door edge flush with cabinet lines

• One black door trim piece as shown

• Disconnect power to the appliance before starting any repairs
• Trim typically snaps or screws into place; remove the door gasket if needed for access
• Use hand tools only and avoid sharp force to prevent cracking adjacent parts
• If fasteners are present, keep track of screws and reinstall securely; test door alignment after install

A replacement shield that protects internal refrigerator components from damage and keeps nearby parts securely covered. Replaces a worn or cracked cover so panels and wiring stay shielded during normal use. What it does:

• Covers and protects vulnerable components from accidental contact and debris
• Helps maintain proper clearance between parts to prevent rubbing or interference
• Restores a finished appearance where the original shield is damaged
• Useful when the original cover is cracked, broken, or missing

• Always unplug the appliance or shut off power at the breaker before servicing
• Handle the part carefully to avoid sharp edges and to prevent further damage
• Basic tools (screwdriver or nut driver) may be required for removal and installation

This insulation panel fits inside the refrigerator cabinet to help maintain consistent temperatures and reduce heat transfer. It preserves cooling efficiency and helps minimize frost and condensation when the appliance is operating properly. What it does:

• Provides thermal barrier between the cabinet and outer shell to help maintain internal temperature
• Helps reduce frost buildup and interior condensation when sealing and cooling systems are functioning
• Can improve energy efficiency by minimizing unwanted heat gain
• Dampens vibration and can reduce operating noise from the compressor area

• Disconnect power to the appliance before starting any repair to avoid electric shock
• Handle insulation carefully—avoid compressing or tearing the material to retain thermal performance
• Remove interior panels or shelving as needed to access the installation area; keep track of fasteners
• If the original insulation is damaged or contaminated, replace it and check nearby seals and gaskets for proper fit

The Inner Door Glass is an  OEM replacement part for Frigidaire ranges. It is responsible for providing a safe viewing window into the oven cavity while protecting interior components from external damage.  

Causes of a bad inner door glass include normal wear and tear such as chips or cracks developing from years of use. Accidental impact or thermal shocks from sudden temperature changes can also compromise the integrity of the glass.

Symptoms of a bad inner door glass:

• Cracks or breaks visible in the glass
• Difficulty seeing into the oven cavity clearly 
• Increased risk of heat escaping when the oven is in use
• Potential safety hazards if glass cracks or shatters  

This genuine Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore gas ranges.

Size: 3/4 inch od x 1/4 inch id.

The Handle Mounting Screw is an OEM part for Frigidaire ranges. This screw secures the handle to the oven door, ensuring it remains firmly attached and allows for easy opening and closing of the oven.

Causes of a bad handle mounting screw can include wear and tear from frequent use, over-tightening, or accidental impact that damages the threads or head of the screw.

Symptoms of a bad handle mounting screw include:

• The oven handle feeling loose or wobbly
• Difficulty in opening or closing the oven door
• The handle detaching from the door
• Visible damage or wear to the screw

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Seal is an OEM part for Frigidaire ranges. This seal creates a tight barrier to prevent heat from escaping during cooking. Maintaining a proper seal ensures that the oven operates efficiently, maintains the correct temperature, and provides even cooking results.

Causes of a bad range door seal can include wear and tear from regular use, exposure to high temperatures, or damage from cleaning tools.  

Symptoms of a bad range door seal include:

• Heat escaping from around the oven door
• Uneven cooking or longer cooking times
• Visible cracks, tears, or deformation on the seal
• The oven door not closing tightly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This hinge is the replacement pivot that supports and guides a refrigerator door so it opens and closes smoothly. It restores proper door alignment and helps maintain a tight seal for efficient cooling. What it does:

• Provides a stable pivot point so the door swings freely and stays aligned
• Helps the door close fully to maintain the internal temperature and seal
• Replaces worn or damaged hinge hardware that can cause sagging or rubbing
• Reduces noise from a loose or binding door pivot

• Disconnect power to the appliance and remove contents or support the door before working to prevent injury or damage.
• Use the correct tools and keep track of mounting screws and any spacers; some installations require removing the door.
• Realign and test the door movement after installation; adjust as needed per your model's instructions.

This surface burner cap fits gas ranges and cooktops. It sits atop the burner head to shape the flame and shield the burner from spills, helping restore smooth ignition and consistent, even heat output.

• Shapes and distributes the burner flame for more even cooking
• Protects the burner head from spills and debris
• Helps ensure reliable ignition and a stable, blue flame
• Common signs it's needed: missing/damaged cap, uneven or yellow flames, burner slow to light, rattling cap

What's included: One surface burner cap. Install notes:

• Turn the burner off and allow the cooktop to cool completely before servicing.
• Remove the grate and lift off the old cap; clean the burner head and ports if needed.
• Center the new cap on the matching burner head so it sits level and fully seated.
• Reinstall the grate and test; realign the cap if the flame is uneven.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

Size: 8-18ab x 0.5 inch.

This is a replacement adhesive label used to restore legible identification or instruction markings on the appliance. Replacing a damaged or missing label helps keep model, rating and safety information readable for service and ownership. What it does

• Restores faded, torn or missing identification and rating information
• Makes model/serial and safety markings easy to read during service
• Helps ensure important usage or caution text remains visible
• Prevents further wear where original adhesive label has peeled

• One replacement adhesive label

• Install on a clean, dry surface; wipe area with isopropyl alcohol and let dry before applying
• Align carefully—adhesive is permanent and difficult to reposition once set
• Use gloves to avoid contaminating the adhesive or leaving fingerprints
• Disconnect power before working in the area

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts

Size: 8-32t x 0.500 inch. Color: Black.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.