Parts for Frigidaire FGIH3047VFE: Door Parts

This Door Trim Kit replaces the perimeter trim on the appliance door, restoring a clean, factory-finished look and secure fit of the door frame components. Use when the original trim is cracked, warped, missing, or discolored.

• Frames and protects the outer edge of the door while concealing fasteners for a finished appearance
• Helps maintain proper placement of door panels/liners where designed
• Common symptoms: cracked or missing trim, loose/rattling trim, visible gaps, or discoloration
• Replace when trim no longer stays attached or is damaged

• Disconnect power to the appliance before servicing; allow all surfaces to cool
• Open the door and note trim orientation; take a photo for reference
• Use non-marring tools and protective gloves to avoid scratching finishes or injury
• After installation, verify the door opens/closes smoothly and does not rub or bind

A replacement shield that protects internal refrigerator components from damage and keeps nearby parts securely covered. Replaces a worn or cracked cover so panels and wiring stay shielded during normal use. What it does:

• Covers and protects vulnerable components from accidental contact and debris
• Helps maintain proper clearance between parts to prevent rubbing or interference
• Restores a finished appearance where the original shield is damaged
• Useful when the original cover is cracked, broken, or missing

• Always unplug the appliance or shut off power at the breaker before servicing
• Handle the part carefully to avoid sharp edges and to prevent further damage
• Basic tools (screwdriver or nut driver) may be required for removal and installation

This refrigerator cabinet insulation panel helps keep cold in and heat out to improve cooling consistency and efficiency. It replaces damaged or missing insulation to reduce frost, hot spots, and excess compressor run time. What it does:

• Provides thermal barrier between the cabinet and outer shell to retain cold air
• Helps reduce frost buildup and condensation inside the cabinet
• Can improve cooling performance and reduce excessive compressor cycling
• Dampens vibration and reduces operating noise

• Disconnect power and empty the appliance before beginning any repair
• Remove interior panels or shelves as needed to access the insulation; follow model-specific service instructions
• Handle insulation carefully to avoid tearing; use gloves and eye protection when trimming or repositioning
• If adhesive or clips are damaged, replace with OEM fasteners

This insulation panel fits inside the refrigerator cabinet to help maintain consistent temperatures and reduce heat transfer. It preserves cooling efficiency and helps minimize frost and condensation when the appliance is operating properly. What it does:

• Provides thermal barrier between the cabinet and outer shell to help maintain internal temperature
• Helps reduce frost buildup and interior condensation when sealing and cooling systems are functioning
• Can improve energy efficiency by minimizing unwanted heat gain
• Dampens vibration and can reduce operating noise from the compressor area

• Disconnect power to the appliance before starting any repair to avoid electric shock
• Handle insulation carefully—avoid compressing or tearing the material to retain thermal performance
• Remove interior panels or shelving as needed to access the installation area; keep track of fasteners
• If the original insulation is damaged or contaminated, replace it and check nearby seals and gaskets for proper fit

The Inner Door Glass is an  OEM replacement part for Frigidaire ranges. It is responsible for providing a safe viewing window into the oven cavity while protecting interior components from external damage.  

Causes of a bad inner door glass include normal wear and tear such as chips or cracks developing from years of use. Accidental impact or thermal shocks from sudden temperature changes can also compromise the integrity of the glass.

Symptoms of a bad inner door glass:

• Cracks or breaks visible in the glass
• Difficulty seeing into the oven cavity clearly 
• Increased risk of heat escaping when the oven is in use
• Potential safety hazards if glass cracks or shatters  

This genuine Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore gas ranges.

The Screw is an OEM replacement part for Frigidaire appliances. This screw is used to securely fasten components, such as panels, brackets, or internal parts, ensuring the appliance remains stable and functions correctly. Its precise design ensures a snug fit and reliable performance in the designated area of the appliance.

Over time, screws can become stripped, corroded, or loosened due to vibrations, frequent use, or environmental factors. A damaged or missing screw may lead to instability, misaligned components, or operational issues with the appliance.

Symptoms of a bad or missing screw include:

• Loose or misaligned panels or components
• Rattling or unusual noises during operation
• Difficulty in securing parts during repairs or adjustments
• Parts becoming detached or unstable

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Seal is an OEM part for Frigidaire ranges. This seal creates a tight barrier to prevent heat from escaping during cooking. Maintaining a proper seal ensures that the oven operates efficiently, maintains the correct temperature, and provides even cooking results.

Causes of a bad range door seal can include wear and tear from regular use, exposure to high temperatures, or damage from cleaning tools.  

Symptoms of a bad range door seal include:

• Heat escaping from around the oven door
• Uneven cooking or longer cooking times
• Visible cracks, tears, or deformation on the seal
• The oven door not closing tightly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This door hinge secures and guides a refrigerator or freezer door, restoring proper alignment and smooth opening and closing. Replace a worn or damaged hinge to help prevent door sag and improve seal integrity. What it does:

• Supports the door and provides a pivot point for smooth swinging motion
• Maintains door alignment for an even seal against the cabinet
• Helps prevent door sag, scraping, or uneven gaps that can let cold air escape
• Works with existing hinge hardware to restore reliable door operation

• Disconnect power and empty or support the door before removing hinge fasteners
• Have a second person or a support prop hold the door while replacing the hinge
• Use appropriate hand tools and avoid overtightening fasteners to prevent damage
• Adjust as needed per manufacturer instructions

The Handle is an OEM part for Frigidaire ranges. Crafted from durable heat-resistant metal, these handles provide safe, ergonomic access to oven interiors during cooking cycles.  

Prolonged exposure to elevated oven temperatures causes typical discoloration of painted finishes as well as looseness from load stresses reducing tactile control over years. Cooking convenience decreases without gripable surfaces.

Symptoms indicating handle wear include:

• Faded, chipped, or flaking handle finishes  
• Loose, rattling, or awkward movement from placement
• Deteriorating mounting attachments risking accidental falls

Replacing with this OEM Frigidaire handle restores tactile guidance into the cooking cavity. Compatibility also fits some Kenmore, Electrolux, and Gibson ranges renewing secure doorknob function through authorized maintenance. 

This replacement door cap is the molded end cap that finishes and protects the edge of a refrigerator door, restoring a clean appearance and covering exposed hardware. It helps keep the door trim sealed and cosmetically intact. What it does

• Covers and protects the exposed door edge and hinge area from damage and wear
• Restores a finished, factory appearance when the original cap is cracked or missing
• Helps prevent dirt and moisture from collecting in the exposed trim area
• Reduces rubbing or misalignment caused by damaged door trim

• One door cap/end cap

• High-level, snap-on or screw-retained installation; follow the manufacturer's diagram for the correct orientation
• Remove the door or hinge only if required by the manufacturer's instructions
• Disconnect power to the appliance before working near electrical components or removing door-mounted controls
• Use basic hand tools and take care not to scratch painted surfaces during installation

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts