Parts for Frigidaire FPTR18D3RS4A: 02 - Door Parts

Freezer door gasket keeps an airtight seal around the door to lock in cold air and keep moisture out. Replacing a worn, gray magnetic gasket helps maintain temperature, reduce frost and condensation, and support consistent cooling performance.

• Seals the freezer door perimeter to prevent warm-air leaks
• Helps hold set temperature and reduce frost/condensation
• Replaces torn, warped, or permanently compressed gaskets
• Common symptoms: frost along door edges, door not closing flush, warm spots, or longer run times

• Disconnect power to the refrigerator before servicing
• Warm the gasket in hot water or with a low-heat hair dryer to relax shipping creases; do not overheat
• Seat the gasket bead into the door channel; start at corners and work evenly around
• After installation, check the seal with a paper test and allow up to 24 hours for the gasket to conform; adjust door alignment if needed

The Refrigerator Door Gasket is an OEM replacement part for Frigidaire refrigerators. As a crucial sealing component, it works to prevent air and temperature leakage around the refrigerator door. The gasket creates an air-tight seal when the door is closed, maintaining proper cooling and preserving freshness inside.

The causes of a bad gasket can include cracks, dried-out or degraded rubber, or damage from repeated door openings and closings.

Symptoms of a bad gasket include:

• Increased humidity or moisture inside the refrigerator
• Difficulty keeping temperatures low enough
• Frost or ice build-up around the door perimeter

This OEM part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Shelf is an OEM replacement part for Frigidaire refrigerators. This gallon door shelf measures about 23 inches wide from inside to inside. 

Causes of a bad door shelf can include frequent use, overloading, or accidental impacts, leading to cracks, breaks, or warping. When the door shelf is damaged, it can compromise the stability and security of stored items, making it less effective for storage needs.

Symptoms of a bad part may include- 

• Cracks or breaks in the plastic
• Difficulty holding items securely in place 
• Shelf not staying attached to the door 
• Difficulty closing the door

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Refrigerator Door Shelf is an OEM replacement part for Frigidaire refrigerators that provides storage space on the refrigerator door. This shelf is designed to fit securely on the door, offering a convenient place to store condiments, bottles, and other items for easy access. The package includes one door shelf. The shelf measures approximately 23”.

Over time, the shelf can crack or break due to frequent use, overloading, or accidental impacts. A faulty door shelf can result in items falling or not being securely held in place.

Symptoms of a bad part include:

• Sagging or broken shelves
• Items falling off the shelf
• Difficulty in opening or closing the refrigerator door

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Dairy Door is an OEM replacement part for  Frigidaire side-by-side refrigerators. Located inside the fresh food compartment, it provides a dedicated storage area for milk, yogurt, cheese and other dairy products requiring colder temperatures. The door measures approximately 9 inches wide and 5 inches high.

Causes of a bad dairy door include normal wear from repeated opening and closing over time. Exposure to spills inside the refrigerator can also potentially damage door shelf components or seals.

Symptoms of a bad dairy door are: 

• Difficulty opening or closing the door smoothly  
• Door alignment issues where it does not sit flush in the frame
• Leaks or moisture inside the dairy storage area
• Damage or cracks in shelf supports or gasket seals

This OEM part is also compatible with models from brands like Electrolux, Gibson, and Kelvinator brand models.

NOTE: For white use 240337701

The Freezer Door Shelf is an OEM part for Frigidaire side-by-side refrigerators. It provides adjustable storage within the freezer compartment for easy access to items. The shelf measures about 24 inches long and 5 inches wide.

Causes of a bad freezer door shelf can include wear over time from repeated loading/unloading that causes scratches or cracks in the lightweight plastic. Exposure to slushy spills may promote material breakdown if not cleaned promptly. 

Symptoms of a bad freezer door shelf include:

• Sagging or inability to bear weight of frozen packages
• Breakage leaving smaller pieces that could fall  
• Discoloration compromising appearance and sanitation
• Shelving that won't stay level or properly positioned

This genuine Frigidaire shelf is also compatible with Electrolux and Kenmore models.

This plug button is a small control panel push button used on select Frigidaire appliances to replace a worn or broken button and restore normal user control. It snaps into the panel for a clean, factory-fit appearance. What it does:

• Acts as the tactile push button used to operate a specific control or function on the appliance
• Replaces cracked, loose, or missing buttons that prevent consistent button actuation
• Restores proper contact engagement so the control registers presses reliably
• Helps eliminate cosmetic damage and keeps the control surface sealed against debris

• One plug button

• Snap-in replacement; remove power to the appliance before attempting any service
• If button is attached to an electronics assembly, handle boards and connectors carefully to avoid damage
• Use basic hand tools as needed and avoid forcing parts—verify orientation before snapping into place

Note: Quantity is one plug button.

This full refrigerator door replaces a damaged or worn outer door to restore the appliance's appearance and proper access to the fresh-food compartment. It provides a solid closure surface and helps maintain normal cooling performance when properly installed. What it does:

• Replaces a dented, cracked, or cosmetically damaged outer refrigerator door
• Restores proper sealing and alignment when used with an intact gasket and hinge hardware
• Provides the mounting surface for handles, trim, and door-mounted storage
• Helps prevent cold air loss from the fresh-food compartment when installed correctly

• Disconnect power and empty the door of food and removable bins before beginning
• Many doors require two people to safely lift and align during installation
• Retain and reuse original hinges, pins, and hardware unless the replacement explicitly includes them

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Screw Kit is an OEM part for Frigidaire appliances. It contains various screws specifically designed to fit and secure different components of Frigidaire appliances, ensuring a tight and secure assembly. This kit is essential for both initial installations and for making repairs or replacements to existing appliances, providing the necessary hardware to maintain or restore the structural integrity of your appliance.  These screws are #10-16 x .500 inches long and can be loosened or tightened using either a Phillips-head or square-head screwdriver.

Symptoms of needing a new Screw Kit include:

• Loose components or panels on your appliance due to missing or damaged screws.
• Inability to securely fasten parts during assembly or repairs, which can lead to operational issues or safety hazards.
• Screws stripping or corroding over time, which can compromise the stability and durability of the appliance.

Causes for replacing screws can include mechanical stress that causes screws to loosen or fall out, environmental factors like moisture leading to corrosion, or accidental damage during cleaning or maintenance.

This screw kit is designed to be universally compatible with various Frigidaire models, ensuring that you have the right screws for a range of repair needs.

The Hinge Bearing is an OEM part for Frigidaire refrigerators. It is designed to facilitate the smooth opening and closing of the refrigerator door by providing a pivot point for the door hinge. This bearing ensures that the door moves easily and remains properly aligned, helping to maintain a tight seal and optimal refrigerator performance.

Causes of a bad hinge bearing can include regular wear and tear from frequent use, exposure to moisture or temperature changes, and physical damage due to accidental impacts. Over time, these factors can cause the hinge bearing to wear out, become loose, or break, affecting the door's functionality.

Symptoms of a bad hinge bearing include:

• Difficulty opening or closing the refrigerator door
• The door not staying in place or sagging
• Unusual noises, such as squeaking or grinding, when the door is moved
• The door not sealing properly, leading to temperature fluctuations inside the refrigerator

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement part is a set screw, and it is intended for use in different types of appliances. This is a genuine replacement part made by Frigidaire. This screw set is compatible in many different areas of the appliance. Screws are typically used for keeping parts of the machinery secure and in place. It is possible that screws can become loose over time and need to be replaced. A new screw set might be needed if the user notices parts of the appliances are becoming loose or are falling off. This can be due to screws becoming stripped over time or if the appliance is bumped during transport. It is typically easy to replace screws. Simply remove the old screw and replace it with a new part. The only tools needed for this repair are a screwdriver and possibly pliers if the damaged screw is stuck in place.Note that this is a genuine OEM replacement part and is sourced from the manufacturer. This set screw is sold individually.

The Door Handle Screw is an OEM part for Frigidaire refrigerators. This screw secures the door handle to the refrigerator door, ensuring a firm and stable grip for opening and closing the door.

Causes of a bad door handle screw can include regular wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or stripping. A faulty screw can lead to a loose or wobbly door handle, making it difficult to operate the refrigerator.

Symptoms of a bad door handle screw include:

• The door handle feeling loose or coming off
• Difficulty in securely tightening the handle
• Visible rust or corrosion on the screw
• Stripped threads on the screw or handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This 3/32" screwdriver is the service tool used to access and adjust small screws on appliances, making routine panel and control adjustments easier and more precise. Handy for basic repairs and maintenance. What it does:

• Fits 3/32" slotted screws commonly found on control panels, trim, and small fasteners
• Allows removal and installation of small service screws for access to internal components
• Helps correct loose screws that can cause rattling or misaligned panels
• Provides better fit than oversized drivers to reduce screw head damage

• Always disconnect power to the appliance before performing service or repairs
• Use the correct 3/32" blade size to avoid stripping screw heads
• Apply steady pressure and avoid excessive torque; use hand force only unless otherwise specified

This is a service wrench used to loosen and tighten appliance fasteners for maintenance and repairs, making access and part replacement easier for technicians and DIYers. Durable tool designed for specific appliance fastener sizes. What it does:

• Provides the correct fit and leverage for removing or installing designated appliance nuts, bolts, and fittings
• Helps safely access internal components during service and part replacement
• Reduces risk of rounding fasteners compared with improvised tools
• Useful for routine maintenance tasks and repair procedures that require a dedicated wrench

• One wrench

• Use the wrench only for its intended appliance fasteners; avoid excessive force
• Disconnect power and water to the appliance before beginning service
• Wear safety gloves and eye protection when working on appliances

This grille clip is a small plastic retainer that secures a refrigerator grille or trim piece to the cabinet, keeping the front panels aligned and preventing rattles or gaps for a tidy appearance. What it does:

• Secures the lower/front grille or trim to the appliance cabinet to hold it in place
• Prevents grille movement, rattling, or sagging that can occur with worn clips
• Helps maintain a tight fit between trim and cabinet for a finished look
• Simple replacement part when existing clip is cracked, broken, or missing

• One grille clip

• Typically snaps into place; inspect mating slot and clip orientation before installing
• Replace any damaged adjacent clips for even support and fit
• Work carefully to avoid damaging the grille or surrounding trim