Parts for Frigidaire FRT16PDFD0: 02 - Door Parts

Color: White

The Freezer Door Gasket is an OEM part for Frigidaire refrigerators. This gasket creates a seal around the freezer door to prevent warm air from entering and cold air from escaping, ensuring the freezer maintains its optimal temperature.

Causes of a bad freezer door gasket can include wear and tear over time, exposure to harsh cleaning chemicals that degrade the material, or physical damage from frequent use or mishandling.

Symptoms of a bad freezer door gasket include:

• Noticeable gaps or cracks in the gasket
• Frost buildup inside the freezer
• Increased energy consumption
• The freezer door not closing properly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Refrigerator Gasket is an OEM replacement part for Frigidaire models. It provides a sealing barrier around the door frame, preserving cool air inside the refrigerator compartment. Composed of durable synthetic materials, the contoured gasket creates an insulating shield.

Causes of a faulty gasket include cracks or breaks from over-closure of the refrigerator door. Deterioration from extended exposure to temperature extremes can also impact integrity over time.

Symptoms of a bad refrigerator gasket include: 

• Inability to maintain a consistent internal cooling temperature
• Accumulation of moisture or frost at door edges  
• Visible gaps allowing warm external air to infiltrate
• Air leaks around the refrigerator opening

Compatible models include brands produced by Electrolux, Gibson, and Kelvinator.

Rack is approximately 25 3/4" long. It may have to be cut for certain models.

Contains both left and right hand side

Color: white. (Used on LH & RH side)

Rack is approximately 25 3/4" long. It may have to be cut for certain models.

This part has been discontinued and is no longer available.

A small white plug button that covers the lower front door opening to restore the refrigerator's finished look and keep out dirt and moisture. Simple cosmetic replacement for worn, broken, or missing door plugs. What it does:

• Covers an unused hole or fastener opening on the refrigerator's lower door front
• Restores finished appearance and helps keep out dust and moisture
• Prevents squeaks or movement from a loose/ missing plug area
• Matches factory white finish for a clean, OEM look

• One (1) white plug button for lower door front

• Usually a simple push-fit—align and press into the hole until fully seated
• If stubborn, use a small flat tool carefully to avoid scratching the door
• Power disconnect not typically required for this cosmetic part, but use caution when working around door hardware

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Stick on

Snap in

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener

Size: Approximate 2.5 inches thick, 33 inches wide and 70 inches long.