Parts for Frigidaire FRT21PRCB5: 02 - Door Parts

Rack is approximately 25 3/4" long. It may have to be cut for certain models.

Contains both left and right hand side

Color: white. (Used on LH & RH side)

Rack is approximately 25 3/4" long. It may have to be cut for certain models.

This part has been discontinued and is no longer available.

A small white plug button that covers the lower front door opening to restore the refrigerator's finished look and keep out dirt and moisture. Simple cosmetic replacement for worn, broken, or missing door plugs. What it does:

• Covers an unused hole or fastener opening on the refrigerator's lower door front
• Restores finished appearance and helps keep out dust and moisture
• Prevents squeaks or movement from a loose/ missing plug area
• Matches factory white finish for a clean, OEM look

• One (1) white plug button for lower door front

• Usually a simple push-fit—align and press into the hole until fully seated
• If stubborn, use a small flat tool carefully to avoid scratching the door
• Power disconnect not typically required for this cosmetic part, but use caution when working around door hardware

A small black replacement plug button that restores a clean, finished appearance and helps keep controls and openings free from dirt and moisture. Designed as a direct-fit cosmetic and protective cap for compatible appliance openings. What it does

• Covers exposed holes or button openings to prevent debris and spills from entering internal areas
• Restores the original look where a worn or missing plug detracts from the appliance finish
• Holds in place to protect underlying components from accidental contact
• Useful when replacing control bezels or trim that require a matching push-in cap

• Disconnect power to the appliance before performing any service work
• Press the plug button squarely into the opening until it snaps into place; no special tools typically required
• Inspect the mounting hole for damage or debris before installing to ensure a secure fit
• If the part does not seat properly, do not force it; verify correct part and orientation

Replace a cracked or broken handle with this black refrigerator door handle. It restores a solid, comfortable grip so you can open and close the door normally and keep your appliance looking clean and intact.

• Restores a secure handhold for opening and closing the door
• Common fix for cracked, broken, or missing door handles
• Helps address a wobbly handle when the handle's mounting points are damaged
• Refreshes the appliance's appearance with a matching black finish

• Disconnect power to the appliance before servicing
• Remove any decorative screw covers if present, then support the handle while removing mounting screws
• Align the new handle with existing mounting holes and tighten screws evenly—do not overtighten
• Check that the handle is secure and the door opens and closes normally

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Stick on

Color: Chrome

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener

Size: Approximate 2.5 inches thick, 33 inches wide and 70 inches long.