Parts for Ge DHDVH66EH3BB: 03 - Door Parts

Package of 12

This leveling leg threads into the base of your appliance to provide a stable, adjustable footing. Replacing a worn or missing leg helps keep the cabinet level, reducing vibration and noise for smoother, safer operation.

• Adjusts height so the unit can be leveled on uneven floors
• Maintains solid floor contact to minimize rocking or walking
• Helps reduce vibration and rattling noises during operation
• Signs you need this part: appliance wobbles, sits unevenly, or a foot is missing/damaged

• Disconnect power; for gas units, also shut off the gas supply
• With assistance, carefully tilt or raise the appliance to access the leg
• Unscrew the old leg and thread in the new leg by hand; use a wrench if needed
• Level the unit front-to-back and side-to-side; ensure all legs firmly contact the floor

This Viper cover is a replacement exterior trim piece that restores the appliance's finished appearance and protects internal components from dust and damage. It matches the original fit and finish for a clean, factory look. What it does:

• Covers and protects control housing and internal components from debris and accidental contact
• Restores cosmetic appearance where the original cover is scratched, dented, or missing
• Helps reduce rattles or vibration caused by a loose or damaged cover
• Provides the correct mounting points and alignment for secure installation

• Disconnect power to the appliance before beginning any repair
• Handle carefully to avoid scratching the finish and watch for sharp edges
• Installation typically requires removing trim or control fasteners and snapping or screwing the cover into place
• If clips or screws are damaged, replace them to ensure a secure fit

This replacement granite-finish cover restores the finished look and protects the exposed area on your refrigerator dispenser/door assembly. It's a direct-fit cosmetic panel that helps hide mounting points and repaired areas. What it does:

• Replaces a cracked, chipped or missing decorative cover to restore the refrigerator's appearance
• Hides mounting hardware and opening edges for a finished look
• Helps protect the underlying components from light contact and cosmetic damage
• Matches appliance finish so the door or dispenser area looks uniform

• Disconnect power to the appliance before starting any service that may involve wiring or water lines
• Usually installs with simple fasteners or snaps; save original hardware and note orientation before removal
• Handle carefully to avoid scratching the finish during installation

This levelling leg support bracket secures and stabilizes an appliance leg to keep the appliance level and steady on uneven floors. Restores proper footing to reduce rocking and improve door and drawer alignment. What it does:

• Holds the adjustable levelling leg in place so the appliance sits level and stable
• Helps stop rocking, tipping, and uneven operation caused by a loose or damaged bracket
• Restores proper appliance alignment to improve door and drawer sealing and operation
• Works with the factory levelling leg assembly to transfer weight to the cabinet/frame

• Designed for use with the factory levelling leg assembly;
• Turn off and unplug the appliance and empty any contents before working underneath
• Use basic hand tools; avoid forcing parts to prevent damage to cabinet or fasteners
• If mounting fasteners are damaged or missing, replace them with OEM-equivalent hardware

The Power Terminal Block is an OEM part for GE dryers. This component serves as the connection point for the dryer's power cord, distributing electrical power to the various internal components of the dryer. It ensures that the dryer receives the proper electrical supply needed for its operation.

Causes of a bad power terminal block can include electrical overloads, corrosion from moisture exposure, and loose or frayed wiring connections. These issues can lead to improper power distribution or complete loss of power to the dryer.

Symptoms of a bad power terminal block include:

• The dryer not starting or losing power during a cycle
• Intermittent electrical issues or power surges
• Visible signs of damage such as burn marks or melted plastic
• Electrical arcing or sparking from the terminal block area

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Color: White.

This terminal block cover shields the dryer's rear power connection at the terminal block. Replace a missing or damaged cover to help protect wiring from accidental contact and lint intrusion, maintaining a cleaner, safer connection area.

• Covers and helps protect the power cord terminals and wiring at the rear terminal block
• Helps prevent accidental contact and keeps lint/debris away from the connection area
• Restores a secure cover when the original is cracked, warped, or missing
• Common signs you need this part: exposed terminals at the rear panel, a loose or broken cover

• Disconnect power to the dryer before servicing
• Access the terminal block from the rear; remove the retaining fastener(s) and lift off the old cover
• Ensure the cord strain relief and wiring are properly positioned, then set the new cover in place and secure it

A replacement strain relief bracket that secures the appliance power cord at the entry point, protecting wiring and the terminal connection from pull and wear. Restores proper cord routing for safer, more reliable electrical connection. What it does:

• Secures the power cord where it enters the appliance to prevent tension on terminals and wiring.
• Helps reduce intermittent power, loose connections, or arcing caused by a tugged or poorly routed cord.
• Maintains correct cord routing and support to match the original mounting location and fit.
• Useful when the original bracket is cracked, broken, or no longer holds the cord firmly in place.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Access is typically from the rear; remove the back access panel to reach the cord entry and terminal block.
• Remove mounting screws holding the old bracket, position the cord, and secure the new bracket without over-tightening; reuse original hardware if appropriate.
• Inspect the power cord and terminals for damage—replace damaged wiring.

Size: 8-32 t. Includes 12 screws.

Includes 12 screws. Size: 8-18 ab.

This replacement part is a control board that has been manufactured by General Electric and is compatible with dryers. This part works by allowing the user to select the desired functions such as the drying time or the temperature. Control boards are subject to wear and tear over time, which may cause them to deteriorate or become faulty, requiring replacement. Before attempting any sort of repairs, ensure that the dryer has been entirely disconnected from all power sources to prevent the risk of injury, particularly from electrocution. Work gloves should also be worn.This is a genuine OEM part that has been sourced directly from the manufacturer. This is an authentic part made of high-quality, durable, non-corrosive materials and is compatible with dryers manufactured by General Electric, Hotpoint, RCA, and some other brands. This part is only sold individually.

This main power board support is the mounting bracket that secures the appliance's main control board, helping maintain stable connections and prevent board movement that can cause intermittent power or control issues. Designed for direct OEM fit. What it does:

• Provides a secure mounting point for the main power/control board
• Keeps board aligned to prevent loose connectors and intermittent electrical contact
• Reduces vibration-related stress on solder joints and components
• Helps prevent damage from board shifting during use or transport

• One main power board support bracket

• Disconnect power at the breaker or unplug the appliance before starting any work
• Handle the control board carefully and avoid contact with circuit traces or components
• Use existing screws or hardware unless replacement fasteners are specified by the manufacturer