Parts for Ikea K00462152A: Door Parts

Replacement refrigerator door assembly that restores a damaged or dented outer door to proper fit and sealing, helping the appliance maintain interior temperature and reduce cold-air leaks. What it does:

• Replaces a cracked, dented, or warped outer door panel to restore appearance and function.
• Helps stop cold air from escaping, reducing frost and moisture buildup inside the compartment.
• Restores door alignment and latch engagement so the door closes securely.
• Returns the proper surface for attached trim, handles, and exterior controls.

• Disconnect power to the appliance before starting any repair.
• Doors can be heavy and awkward—have a second person assist to avoid injury or damage.
• Keep existing hinges, mounting screws, and hardware unless replacement hardware is explicitly supplied by the part listing.
• After installation, check door alignment and gasket seating; make small hinge adjustments as needed to ensure a proper seal.

The Gasket is an OEM part for Frigidaire refrigerators. As a component of the refrigerator door, the gasket provides an important insulation barrier, sealing in cold air and keeping warmer air out. It works to maintain consistent temperatures within the refrigerator compartment. 

Causes of a bad gasket can include cracks or breaks due to aging and repeated opening and closing of the door. Gaskets can also become compressed or misshapen over time, reducing their effectiveness.

Symptoms of a bad gasket include:
 

• Increased humidity or moisture buildup inside the refrigerator  
• Frost or condensation appearing around the doors and inside walls
• Higher power bills due to the refrigerator having to work harder to maintain temperatures
• Warm air leaking in and causing temperature fluctuations inside the fridge

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

This replacement gasket restores a tight seal between mating parts in your appliance. Replacing a worn seal helps stop leaks and keeps performance steady by maintaining proper containment during normal operation.

• Creates a compressible barrier between components to prevent leaks and seepage
• Maintains proper system performance by preserving the intended seal
• Helps reduce vibration and wear at the joint
• Replace if cracked, flattened, brittle, warped, or if leaks are present around the connection

• Disconnect power; shut off water or gas if applicable
• Allow the unit to cool and relieve any pressure before service
• Clean and dry mating surfaces; remove the old gasket and residue
• Install without stretching; tighten fasteners evenly; do not use sealants unless specified by the manufacturer

This replacement crisper bin restores storage space in your refrigerator by holding fruits and vegetables securely in the fresh-food compartment. Durable, easy-to-clean plastic keeps produce contained and organized. What it does

• Holds fruits, vegetables and other fresh-food items to prevent rolling or shifting
• Protects produce from spills and helps keep the fresh-food compartment organized
• Clear plastic lets you quickly see contents without removing the bin
• Works as a direct-fit replacement for a worn, cracked or missing crisper bin

• One refrigerator crisper bin

• Slide into the crisper opening until it seats; it aligns with the cabinet rails or support ledges
• No tools typically required; remove nearby shelves or drawers first if needed for clearance
• Handle with care—avoid dropping to prevent cracks or chips
• Disconnect power only if removing other components that require access to electrical parts

This bearing supports and helps the dryer drum rotate smoothly, reducing noise and wear for reliable load tumbling. Replace a worn bearing to restore quieter, more even drum movement. What it does:

• Supports the dryer drum on the rear/front shaft so it spins freely
• Reduces metal-on-metal contact that causes squeaks, grinding or rumbling
• Helps maintain proper drum alignment to prevent uneven wear and laundry snags
• Restores smoother rotation when old bearings show play or roughness

• One bearing as shown

• Disconnect power (and gas, if applicable) before starting any repair
• Access may require removing the dryer front or rear panel and drum — your model's service instructions
• Inspect mating shaft and housing for wear; replace or repair damaged components to avoid premature failure

The Bearing is an OEM part for Frigidaire refrigerators. It is primarily used to provide smooth rotation or movement of the condenser fan motor assembly located inside the bottom of the refrigerator compartment. 

Proper ventilation is crucial for refrigerator performance and to prevent premature component failure. The bearing works to ensure the condenser fan motor spins freely without excess friction or noise, properly circulating air through the cooling system. 

Symptoms of a bad bearing include:

• Loud grinding or squealing noises coming from inside the refrigerator
• The condenser fan motor being stuck or seizing up  
• Overheating issues due to impaired airflow
• Premature compressor failure from insufficient cooling

Causes can be normal wear over long periods of operation, lack of maintenance allowing dust/debris accumulation, or accidental impact damage. 

This OEM replacement is also compatible with models by Electrolux, Gibson, Kelvinator, and Kenmore.
 

A small replacement hook used to secure and retain components in place on compatible Frigidaire appliances. Restores proper part alignment so doors, panels or accessories stay mounted and operate correctly. What it does

• Secures a panel, door or accessory to its mounting point to prevent slipping or detachment
• Replaces worn or broken hooks that allow parts to sag, shift, or fall out of place
• Helps restore proper alignment and stable operation of the affected component
• Works wherever the OEM hook is used as a retainer or mounting clip

• The hook shown

• High-level replacement; typically accessed with basic hand tools
• Disconnect power before working on electrical appliances and shut off water for water-connected units
• Inspect the mating surfaces and surrounding fasteners; replace any damaged hardware for best results

The Hook is an OEM part for Frigidaire refrigerators. It helps to ensure a secure and proper closure of the refrigerator door.

A bad hook can be caused by wear and tear, damage, or misalignment. Signs of a faulty door closer hook include the door not closing fully or not staying closed, difficulty in opening or closing the door smoothly, or a loose or wobbly door.

Symptoms of a bad hook can include:

• The refrigerator door not sealing properly
• Excessive force required to open or close the door
• Visible damage or misalignment of the door closer hook

Replace your worn or damaged hook with this genuine OEM part to restore your refrigerator door. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This is a replacement threaded screw used to secure appliance components where the original fastener is missing or damaged. It restores proper attachment so panels, brackets, or small parts stay in place. What it does:

• Secures panels, brackets, or trim to the appliance to prevent movement or rattling
• Replaces missing, stripped, or damaged screws that can allow parts to come loose
• Helps restore proper alignment of parts when used in original mounting locations
• Suitable as a direct-fit replacement when the OEM part number matches

• Disconnect power before working on any appliance and follow all safety precautions
• Use the correct driver or bit to avoid stripping the screw head
• Keep small parts away from children and pets; magnetic trays help during installation