Parts for Kelvinator KRS221LHY0: 03 - Door Parts

This door gasket seals the dishwasher tub opening to prevent water leaks during the wash cycle. A fresh, pliable gasket helps maintain proper water containment and quiet operation.

• Creates a watertight seal around the dishwasher door perimeter
• Helps reduce leaks, puddling, and excessive moisture at the base of the door
• Restores proper door compression and sound dampening

• Disconnect power and turn off water supply before servicing
• Remove the old gasket from the channel; clean the groove of debris and mineral buildup
• Press the new gasket evenly into the channel, aligning the center at the top first
• Close the door to help seat the seal; check for pinches or gaps and adjust as needed

This inner door panel restores the interior surface and structural support for an oven door, helping maintain a proper seal and protecting internal components from heat and debris. It's a direct-replacement exterior/interior panel used during door repair. What it does:

• Replaces a cracked, dented, warped or otherwise damaged inner door panel to restore door rigidity and appearance.
• Protects insulation, wiring and other internal door components from direct contact with cookware, spills and heat.
• Helps maintain an even seal and reduce drafts or heat loss caused by a warped or loose inner panel.
• Stops rattling or vibration caused by loose or broken interior door pieces.

• Disconnect power to the appliance before starting any repair and allow the oven to cool completely.
• Handle panels and any glass carefully; wear cut-resistant gloves and eye protection.
• Installation typically requires removing the door and detaching interior trim and fasteners—keep hardware organized for reassembly.

This part number contains one (1) screw.

The Door Handle Screw is an OEM part for Frigidaire refrigerators. This screw secures the door handle to the refrigerator door, ensuring a firm and stable grip for opening and closing the door.

Causes of a bad door handle screw can include regular wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or stripping. A faulty screw can lead to a loose or wobbly door handle, making it difficult to operate the refrigerator.

Symptoms of a bad door handle screw include:

• The door handle feeling loose or coming off
• Difficulty in securely tightening the handle
• Visible rust or corrosion on the screw
• Stripped threads on the screw or handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener

This nut-anchor is a small mounting insert that provides a secure threaded point in thin sheet metal so screws can fasten panels or components reliably. It restores a solid attachment where the original fastener or threaded hole is missing. What it does:

• Provides a reinforced threaded anchor in thin metal or plastic panels
• Allows screws to tighten without stripping the sheet material
• Stops panels, trim, or assemblies from coming loose or rattling
• Used where a captive nut or threaded insert is required for reassembly

• Install where original nut/insert was located; verify orientation before fastening
• Use the correct screw size and hand-tighten to avoid overtightening or thread damage
• Disconnect power and move the appliance to a safe, stable work area before servicing
• If the original mounting point is severely damaged, consider assessing the surrounding structure for repair