Parts for Kenmore 790.74032314 (79074032314, 790 74032314): Door Parts

This Door Trim Kit replaces the perimeter trim on the appliance door, restoring a clean, factory-finished look and secure fit of the door frame components. Use when the original trim is cracked, warped, missing, or discolored.

• Frames and protects the outer edge of the door while concealing fasteners for a finished appearance
• Helps maintain proper placement of door panels/liners where designed
• Common symptoms: cracked or missing trim, loose/rattling trim, visible gaps, or discoloration
• Replace when trim no longer stays attached or is damaged

• Disconnect power to the appliance before servicing; allow all surfaces to cool
• Open the door and note trim orientation; take a photo for reference
• Use non-marring tools and protective gloves to avoid scratching finishes or injury
• After installation, verify the door opens/closes smoothly and does not rub or bind

This door trim kit restores the finished edge around the appliance door, covering raw edges and fasteners. Replace worn or missing trim to refresh the look and help keep the outer door panel properly seated. What it does:

• Finishes the perimeter of the door and conceals mounting hardware
• Helps retain and align the outer door panel or glass
• Replaces cracked, warped, loose, or missing trim pieces
• Typical symptoms include gaps around the door, loose or rattling edges, or cosmetic damage

• One door trim kit

• Disconnect power to the appliance before servicing
• Wear cut-resistant gloves; door edges and trim can be sharp
• Support or remove the door as required by your model; note screw locations and lengths
• Transfer any clips/screws from the original trim and check door alignment and operation after installation

A replacement shield that protects internal refrigerator components from damage and keeps nearby parts securely covered. Replaces a worn or cracked cover so panels and wiring stay shielded during normal use. What it does:

• Covers and protects vulnerable components from accidental contact and debris
• Helps maintain proper clearance between parts to prevent rubbing or interference
• Restores a finished appearance where the original shield is damaged
• Useful when the original cover is cracked, broken, or missing

• Always unplug the appliance or shut off power at the breaker before servicing
• Handle the part carefully to avoid sharp edges and to prevent further damage
• Basic tools (screwdriver or nut driver) may be required for removal and installation

This insulation panel fits inside the refrigerator cabinet to help maintain consistent temperatures and reduce heat transfer. It preserves cooling efficiency and helps minimize frost and condensation when the appliance is operating properly. What it does:

• Provides thermal barrier between the cabinet and outer shell to help maintain internal temperature
• Helps reduce frost buildup and interior condensation when sealing and cooling systems are functioning
• Can improve energy efficiency by minimizing unwanted heat gain
• Dampens vibration and can reduce operating noise from the compressor area

• Disconnect power to the appliance before starting any repair to avoid electric shock
• Handle insulation carefully—avoid compressing or tearing the material to retain thermal performance
• Remove interior panels or shelving as needed to access the installation area; keep track of fasteners
• If the original insulation is damaged or contaminated, replace it and check nearby seals and gaskets for proper fit

The Inner Door Glass is an  OEM replacement part for Frigidaire ranges. It is responsible for providing a safe viewing window into the oven cavity while protecting interior components from external damage.  

Causes of a bad inner door glass include normal wear and tear such as chips or cracks developing from years of use. Accidental impact or thermal shocks from sudden temperature changes can also compromise the integrity of the glass.

Symptoms of a bad inner door glass:

• Cracks or breaks visible in the glass
• Difficulty seeing into the oven cavity clearly 
• Increased risk of heat escaping when the oven is in use
• Potential safety hazards if glass cracks or shatters  

This genuine Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore gas ranges.

This replacement cabinet frame restores the appliance's front trim for a clean, finished appearance and proper panel alignment. It helps keep edges covered and maintains the door/cabinet fit. What it does:

• Provides the front trim/frame that supports and aligns the appliance cabinet or door panels
• Covers exposed edges for a finished look and helps reduce drafts or light gaps
• Helps eliminate rattling or misalignment caused by a damaged or warped frame
• Matches OEM fit to replace a cracked, bent, or cosmetically damaged frame

• Disconnect power (and water for appliances with water) before beginning any work
• Basic hand tools typically needed; retain all fasteners from the original part for reassembly
• Handle carefully to avoid scratching the finish; check fit before tightening fasteners

The Screw is an OEM replacement part for Frigidaire appliances. This screw is used to securely fasten components, such as panels, brackets, or internal parts, ensuring the appliance remains stable and functions correctly. Its precise design ensures a snug fit and reliable performance in the designated area of the appliance.

Over time, screws can become stripped, corroded, or loosened due to vibrations, frequent use, or environmental factors. A damaged or missing screw may lead to instability, misaligned components, or operational issues with the appliance.

Symptoms of a bad or missing screw include:

• Loose or misaligned panels or components
• Rattling or unusual noises during operation
• Difficulty in securing parts during repairs or adjustments
• Parts becoming detached or unstable

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Seal is an OEM part for Frigidaire ranges. This seal creates a tight barrier to prevent heat from escaping during cooking. Maintaining a proper seal ensures that the oven operates efficiently, maintains the correct temperature, and provides even cooking results.

Causes of a bad range door seal can include wear and tear from regular use, exposure to high temperatures, or damage from cleaning tools.  

Symptoms of a bad range door seal include:

• Heat escaping from around the oven door
• Uneven cooking or longer cooking times
• Visible cracks, tears, or deformation on the seal
• The oven door not closing tightly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This door hinge is a direct-fit replacement part that supports and aligns an appliance door for smooth opening and secure closing. Replacing a worn hinge restores proper fit and prevents door sag, binding, or noisy operation. What it does:

• Provides the pivot point that lets the door open and close smoothly.
• Keeps the door aligned so seals meet and the door closes fully.
• Restores stable door movement and reduces sagging or rubbing.
• Helps stop binding, unusual noises, or doors that don't stay closed.

• Disconnect power to the appliance (and water supply if applicable) before starting work.
• Support the door while removing or installing the hinge to prevent damage or injury.
• Keep original screws and mounting hardware; new fasteners may be required if originals are worn.

This replacement handle restores a secure, comfortable grip for opening and closing your appliance door. It replaces a cracked, loose, or missing handle so operation feels normal again and the appliance maintains a clean, finished look.

• Provides a sturdy handhold to pull/push the door during everyday use
• Attaches to existing mounting points on the door
• Common symptoms: cracked or broken handle, looseness, missing handle, difficulty opening the door
• Helps return the appliance's appearance to like-new condition

• Disconnect power to the appliance before starting; allow hot surfaces to cool
• Wear cut-resistant gloves; support the door/handle while removing hardware
• Reuse existing screws/end caps as applicable; start all fasteners before tightening
• Tighten evenly without overtightening; verify smooth door operation after installation

The Handle is an OEM replacement part for Frigidaire ranges and ovens. Designed for safety and ease of use, this handle allows intuitive opening and closing of the oven door. It provides a sturdy grip to safely access food inside the heating chamber.

Causes of a bad handle can include wear from frequent use over the years, damage from accidental impacts or mishandling, or issues with the mounting fasteners.

Symptoms of a bad handle include:

• Loose, wobbly or difficult operation of the handle
• The handle detaching from the oven door
• Inability to fully open or properly close the door
• Discomfort or safety issues when accessing the hot oven interior

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and select Kenmore range models.

A snap-on protective cap that covers and shields small appliance terminals, posts or hardware from dirt, moisture and accidental contact. Restores the finished appearance and helps reduce corrosion or shorts from exposed connections. What it does:

• Covers exposed terminals, posts or fasteners to keep out debris and moisture.
• Helps prevent accidental contact that can lead to electrical faults or shorts.
• Restores cosmetic finish when a cap is missing, cracked or deformed.
• Common symptom: visible exposed terminal/post or a loose/rattling trim piece.

• Typically installs by pressing the cap onto the mating post until fully seated.
• Always disconnect power to the appliance before accessing electrical components.
• Inspect the mating post or terminal for damage before installing; replace if damaged.

This surface burner cap sits atop the burner head on gas ranges and cooktops, shaping the flame for even heating and shielding the burner from spills. Replace a chipped, warped, or missing cap to restore proper burner performance.

• Shapes and distributes the flame for consistent heat across cookware
• Helps protect the burner head and igniter from drips and debris
• Correct seating supports quick ignition and a clean blue flame
• Common symptoms: uneven or yellow flames, flame lifting, delayed ignition, or constant clicking while lighting

• Allow the burner to cool completely before handling; disconnect power and shut off gas
• Lift off the old cap; clean and dry the burner head surface
• Center the new cap on the burner head so it sits level and does not rock
• Use the cap designated for the correct burner size on your model; re-seat if ignition continues to click or flame is uneven

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

Size: 3/4 inch od x 1/4 inch id.