Parts for Tappan TEF353ASD: 09 - Door Parts

Color: White. This is a 3-sided door trim kit.

A replacement outer glass door panel kit that restores the refrigerator door's appearance and insulating surface. The white outer panel includes foil tape for sealing and finishing the edge for a clean, factory look. What it does

• Replaces a cracked, chipped, or discolored outer glass door panel to improve appearance.
• Restores the door's exterior surface and helps maintain the door edge seal when used with the included foil tape.
• Helps prevent drafts and moisture intrusion at the door edge when installed correctly.
• Matches the original white finish for a factory-style look.

• Disconnect power to the appliance before starting and remove contents from the door.
• Handle the glass panel carefully; wear gloves and eye protection to reduce cut risk.
• Installation typically requires removing the door trim/retainer and carefully replacing the outer glass; keep fasteners and seals organized.

This is a wafer-head screw with a square (Robertson) drive used to secure appliance trim and handle components. It replaces worn or missing fasteners so panels and handles stay firmly attached. What it does

• Secures appliance trim, handles, and lightweight panels where a low-profile wafer head is required
• Square-drive head resists cam-out for reliable tightening
• Common replacement for loose, stripped, or missing fasteners
• Small size fits confined fastening locations without protruding

• One wafer-head square-drive screw (10-24 x 1.6)

• Use the correct square (Robertson) bit to avoid damaging the head
• Tighten securely but avoid over-torquing to prevent thread or component damage
• Disconnect power or follow manufacturer safety guidelines before working near electrical components
• If screw threads are damaged, replace with new threaded insert or correct-size fastener

Size: 3/4 inch od x 1/4 inch id.

This factory seal creates a tight barrier between cooking appliance components to contain heat, moisture, and spills so your unit performs efficiently. Replace a worn or damaged seal to restore proper containment and performance. What it does:

• Seals joints between mating parts to prevent air leaks and liquid intrusion
• Helps maintain stable oven temperatures and efficient preheating
• Reduces escape of heat, odors, and smoke from sealed areas
• Replace if cracked, flattened, torn, or missing

• 1 seal

• Disconnect power; shut off gas supply before servicing
• Allow the appliance to cool completely
• Note the original seal's routing/orientation; remove old seal and clean mating surfaces
• Seat the new seal evenly without stretching; verify proper fit and operation after reassembly

This is the factory handle set for select Frigidaire-built appliances. It restores a secure, comfortable grip and fresh appearance so doors or drawers open and close as intended. What it does

• Provides the handhold needed to open and close the appliance door or drawer
• Replaces cracked, broken, or missing handles
• Helps correct loose or wobbly handles that won't stay tight
• Refreshes worn or scuffed handles for a cleaner look

• Manufacturer-supplied handle set

• Disconnect power before servicing; allow hot surfaces to cool
• Remove interior/hidden mounting screws and the old handle
• Align and secure the new handle; re-use existing hardware/brackets if applicable
• Do not overtighten fasteners; verify smooth door/drawer operation

This replacement surface burner cap sits on top of the gas burner head to focus and distribute the flame for even, efficient heating. Replacing a damaged or missing cap can restore proper ignition and flame pattern. What it does:

• Covers and protects the burner head from spills and debris
• Spreads and concentrates the flame for consistent cooking performance
• Helps prevent yellow, lifting, or uneven flames when properly seated
• Common symptoms: uneven or yellow flames, poor simmer, delayed ignition, chipped/warped/missing cap

• 1 surface burner cap

• Allow the cooktop to cool; disconnect power and shut off gas if servicing beyond simple cap replacement
• Lift off the old cap and clean the burner head surface of residue or debris
• Center the new cap on the matching burner head so it sits level—do not force
• Use the correct cap for the burner position; test ignition and flame after installation

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

Size: 8-18ab x 0.5 inch.

Size: 10-32 x 0.312 inch. Color: Black.

Size: 8-32t x 0.500 inch. Color: Black.