Parts for Whirlpool 8W8TXDWFXT00: 02 - Door Parts

This replacement screw secures panels, brackets, or trim within your appliance. Replacing a worn, stripped, or missing screw restores a tight, rattle-free fit so components stay aligned and operate as intended. What it does:

• Fastens components at the original factory locations specified for this part
• Replaces missing, damaged, or stripped screws to restore holding power
• Helps reduce vibration and rattling from loose parts
• Maintains proper alignment of panels, covers, brackets, and trim

• Disconnect power (and gas, if applicable) before servicing
• Match to the original screw and install in the same location and orientation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver or nut-driver; transfer any washers or spacers from the original hardware if present

The Door Shelf Retainer End Cap is an OEM replacement part for Whirlpool refrigerators. This component is designed to secure and support the end of the door shelves, providing a clean and finished look while preventing items from falling off the edges.

Symptoms of needing to replace the door shelf retainer end cap include:

• Visible cracks, damage, or missing pieces
• Loose or wobbly door shelves
• Items falling off the ends of the door shelves

Causes of a faulty door shelf retainer end cap can include normal wear and tear over time, accidental impact or mishandling, or exposure to excessive moisture or temperature fluctuations.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerator models.

This handle center in biscuit finish restores a clean, uniform look to your refrigerator's door handle assembly. It covers the mounting area and provides a comfortable grip area to help open and close the door smoothly.

• Replaces a worn, cracked, or discolored center section of the door handle
• Helps ensure a secure, comfortable grasp on the refrigerator door
• Cosmetic refresh for handles showing wear or damage
• Common symptoms: loose or broken center handle piece, visible screw areas, cosmetic damage

• Unplug the appliance and wear work gloves for safety
• Remove existing center section or trim as applicable
• Align and snap/secure the new handle center into place per model design
• The handle is firmly seated before use

The Screw is an OEM fastening component specifically designed for securing interior panels and assemblies of Whirlpool brand appliances. 

Causes of a problematic screw include stripping, corrosion, or shearing from repeated installations and removals during service procedures.

Symptoms of faulty screws include:

• Loosened or detached interior panels rattling behind appliance exteriors  
• Reduced structural integrity allowing unnecessary vibrations and noise

Compatible models include brands produced by KitchenAid, Maytag, and some Kenmore.

This replacement screw secures panels, brackets, or trim within your appliance. Replacing a worn, stripped, or missing screw restores a tight, rattle-free fit so components stay aligned and operate as intended. What it does:

• Fastens components at the original factory locations specified for this part
• Replaces missing, damaged, or stripped screws to restore holding power
• Helps reduce vibration and rattling from loose parts
• Maintains proper alignment of panels, covers, brackets, and trim

• Disconnect power (and gas, if applicable) before servicing
• Match to the original screw and install in the same location and orientation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver or nut-driver; transfer any washers or spacers from the original hardware if present

The Fresh Food Door Gasket is an OEM part for Whirlpool refrigerators. It creates an airtight seal around the refrigerator door, helping to maintain the internal temperature and keep food fresh by preventing warm air from entering the refrigerator. This gasket measures approximately 44.70" X 27.16". 

You should replace the fresh food door gasket if it becomes worn out or damaged. Causes of a bad door gasket can include regular wear and tear, damage from frequent opening and closing of the door, and exposure to temperature fluctuations. Over time, the gasket may become brittle, crack, or develop mold.

Symptoms of a bad fresh food door gasket include:

• Warm air entering the refrigerator, leading to higher internal temperatures
• The refrigerator running more frequently or for longer periods
• Visible cracks, tears, or mold on the gasket
• Difficulty in closing the refrigerator door securely

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This screw anchor is a small plastic fastener that secures panels and trim on appliances, preventing screws from stripping or pulling out. It provides a reliable anchor point for screws where threaded material is thin or absent. What it does:

• Creates a secure mounting point for screws in sheet metal, plastic or thin panels
• Helps prevent screw looseness, stripping, and parts that shift or rattle
• Commonly used to hold trim, panels, or interior components in place
• Works with compatible screws to distribute load and stabilize attachments

• Use the correct screw size and length; anchors are made for specific screw diameters—do not force oversize screws
• Align anchor in the prepared hole before driving the screw to avoid cracking the anchor or surrounding material
• Hand-start screws until seated, then tighten gradually—do not overtighten to prevent stripping or damage
• Disconnect power and follow appliance safety procedures before accessing internal panels

This door shelf trim is the front retainer bar that snaps across a refrigerator door bin to keep items in place. Replace a cracked or missing trim to restore secure storage on the door and prevent spills.

• Holds items within the door bin by providing the front retaining edge
• Common failure signs: cracked/broken bar, won't snap or stay in place, items sliding out of the bin
• Restores proper fit and appearance of the door shelf area

• Unplug the refrigerator before beginning any repair
• Lift off the affected door bin to access the trim
• Align the trim tabs with the bin slots and snap into place without forcing
• Verify the bin is seated securely on the door before use

This thimble is a small insert used in the freezer compartment. It reinforces a mounting hole, prevents liner wear, and helps keep attached hardware stable and properly aligned for smooth, quiet operation.

• Serves as a protective bushing for a hole in the freezer compartment liner
• Helps stabilize and align the component secured at that location
• Replaces cracked, worn, or missing inserts that can cause loose hardware, wobbling, or rattling
• Restores proper fit while helping prevent further wear to the liner

• Unplug the refrigerator and clear the work area in the freezer before service
• Remove the fastener/component to access the insert, then pull the old thimble straight out
• Press the new thimble fully into the hole; reinstall hardware without overtightening
• Use care—cold plastic and liner edges can be brittle or sharp

This hole plug covers the screw access on appliance handles for a finished, factory appearance. It helps keep moisture and debris out of the handle cavity while restoring a clean, matching look to the door. What it does:

• Covers exposed handle screw holes for a finished appearance
• Helps prevent moisture, dirt, and food particles from entering the handle cavity
• Restores a color-matched cosmetic finish to the handle area
• Useful when replacing a handle or finishing a repair where the plug is missing

• One biscuit-colored handle hole plug

• Push the plug into the hole until it snaps flush; may require light pressure or a soft mallet
• Remove the old plug by prying gently with a plastic trim tool to avoid scratching the finish
• No electrical disconnection is typically required for this cosmetic part; follow appliance manufacturer guidance for any door/handle work

The Gasket is an OEM replacement part specific to Whirlpool refrigerators. It is a flat sealing gasket located inside the refrigerator cabinet that forms a tight connection between the fill pipe inlet and the refrigerator unit. The gasket plays an important role in preventing water leaks from developing around the fill pipe connection point during regular operation.

Causes of a faulty gasket can include regular wear and tear over time breaking down its sealing ability, as well as mineral deposits accumulating on the gasket surface.

Symptoms of a leaking gasket include:

• Water puddling or flooding inside the refrigerator cabinet
• Visible water dripping or accumulating around the fill pipe inlet
• White mineral residue visible where the gasket makes contact

It is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore branded models.

The Bracket-Door Stop is an OEM replacement part for Whirlpool appliances. This zinc-finished bracket is designed to prevent the appliance door from opening beyond its intended range, protecting both the door and surrounding components from potential damage. It ensures the door stays secure and functions smoothly during regular use.

Symptoms of a bad Bracket-Door Stop include:

• The door overextending when opened
• Difficulty in maintaining the door's position
• Visible bending, cracking, or damage to the bracket

Causes of a failing Bracket-Door Stop can include repeated stress from excessive force when opening the door, normal wear over time, or accidental impacts. A damaged bracket can compromise the door's alignment and overall functionality.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement screw secures panels, brackets, and other components in your appliance so they stay tight and properly aligned. Use it to replace missing, stripped, or rusted hardware and eliminate looseness, rattles, or gaps.

• Fastens parts to the cabinet/frame to maintain structural integrity
• Helps keep panels and assemblies aligned to reduce vibration and noise
• Replaces missing, damaged, or corroded screws during service
• Common fix for loose panels or components that no longer hold securely

• Disconnect power and shut off water or gas before servicing
• Match length and thread to the original screw for proper fit
• Hand-start threads to avoid cross-threading; tighten only until snug—do not overtighten
• Tighten them evenly to ensure proper alignment

Color: Bisque

The Door Shelf Bar is an OEM part for Whirlpool refrigerators. This bar attaches to the interior of the refrigerator door, providing a secure barrier that holds items like bottles, jars, and containers in place on the door shelves. This trim measures approximately 22 inches long. Notably, this door shelf bar can be cut to fit specific dimensions. 

Over time, the door shelf bar can become worn out or damaged due to regular use, heavy loads, or accidental impacts. Causes of a bad door shelf bar include cracking, breaking, or warping of the plastic material, which can lead to items falling out of the shelf or the bar not staying in place.

Symptoms of a bad door shelf bar include:

• The bar becoming loose or detaching from the door
• Items falling off the shelf when the door is opened
• Visible cracks or breaks in the bar
• Difficulty in securing the bar back into place

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement handle restores a secure, easy-to-grip opening point for your appliance door and refreshes its appearance in biscuit color. Designed to match the original fit and finish for a clean, factory look. What it does:

• Replaces a cracked, broken, or worn door handle so the door opens and closes properly
• Provides a stable grip to prevent slips and accidental drops
• Restores cosmetic appearance where paint or finish has chipped or faded
• Helps maintain proper door control and user comfort during normal use

• One replacement handle

• Turn off power to the appliance and remove food/contents from the door area before starting
• Typical installation uses basic hand tools; screws or mounting clips secure the handle to the door
• Keep original fasteners if possible; verify alignment and secure fit before use

The Door Shelf Bin is an OEM part for Whirlpool refrigerators. It provides organized storage on the refrigerator door, allowing quick access to frequently used items like eggs, butter, or condiments.

Causes of a bad door shelf bin can include warping or cracking of the plastic over time due to temperature changes from door opening. Handles may also loosen or break off from heavy use.

Symptoms of a bad door shelf bin include:

• Food items rolling around inside the door
• Loss of organized storage and ability to neatly display contents
• Possible premature spoilage from lack of airflow

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Door Shelf is an OEM replacement part for Whirlpool refrigerators. This component is designed to fit into the door of your refrigerator, offering additional storage space for items such as condiments, bottles, and other small or medium-sized items that need to be readily accessible. 

Causes of damage to the door shelf can range from overloading it with too much weight, accidental impacts from moving items in and out of the refrigerator, or simply the age of the refrigerator contributing to wear and tear over time.  

Symptoms of a bad Door Shelf include:

• Cracks or breaks in the shelf
• The shelf becoming loose or failing to fit securely in the door slots
• Signs of warping or deformation

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The door stop shim positions the stop flush and fine-tunes the door's opening limit. Replacing a worn or missing shim helps restore smooth door operation and protects nearby surfaces from over-travel or rubbing.

• Provides correct spacing behind the door stop for proper alignment
• Helps limit the door swing to the intended stop position
• Can reduce wobble, play, or clicking at the stop point
• Replaces cracked, deformed, or missing shim components

• Disconnect power and support the door as needed to prevent strain
• Remove the door stop fastener(s) and note the original shim orientation
• Place the new shim behind the stop; reinstall hardware and tighten without overtightening
• Open and close the door to confirm stop angle and clearances