Parts for Frigidaire FFET1222UB: Doors Parts

This upper door gasket seals the top door to keep cold air in and reduce moisture intrusion, helping your refrigerator maintain temperature and efficiency. Designed to replace a worn or damaged upper door seal. What it does:

• Creates an airtight seal at the upper door edge to minimize cold air loss and prevent warm air infiltration.
• Helps reduce frost buildup and interior condensation caused by leaks around the door.
• Can reduce excessive run time from the compressor caused by a poor door seal.
• Restores proper door closure and can improve overall cooling consistency.

• One upper door gasket (white), intended for the refrigerator's upper door

• Unplug the appliance or disconnect power before beginning any service.
• Remove food and shelves as needed to access the gasket area safely.
• Clean the gasket channel and mating surfaces before installing the new seal; press the gasket evenly into the retainer to seat it.
• Verify the door closes and seals properly after installation; allow time for the gasket to form to the frame.

This door gasket creates an airtight seal around the refrigerator door to help keep cold air in and warm air out, improving temperature stability and reducing energy use. It replaces a worn, cracked, or misshapen seal. What it does:

• Seals the perimeter of the refrigerator door to maintain proper internal temperature
• Helps prevent frost buildup by blocking warm, moist air from entering
• Reduces compressor run time and energy waste from a leaking seal
• Restores consistent door closing and improves food freshness

• Remove old gasket and clean the mounting channel before installing the new gasket
• Gasket may require gentle heating or realignment for a snug fit; follow OEM instructions
• Check door alignment and hinge operation after install to ensure a full seal
• Disconnect power only and follow all safety warnings

This door stopper secures and limits the swing of a refrigerator/freezer door to prevent over-travel and protect the cabinet and hinge. Replaces a worn or broken stop to restore correct door positioning and smooth operation. What it does:

• Limits door travel to prevent hitting adjacent surfaces or damaging the cabinet
• Absorbs impact to reduce stress on hinges and mounting hardware
• Helps the door stay aligned and close properly if the original stop is missing or damaged
• Commonly used when the door slams, over-rotates, or the stopper is cracked/broken

• One door stopper

• Disconnect power or unplug the appliance if you need to move it or work near electrical components
• Remove the old stopper and install the new part in the same orientation using the existing screw/hole locations
• Do not overtighten fasteners; align stopper so the door contacts it squarely for correct stopping action
• Verify proper door operation and hinge alignment after installation

This door stopper cushions and limits a refrigerator door's travel to prevent over-rotation and reduce slamming for smoother, safer operation. It restores proper door alignment and helps maintain an effective seal when the hinge stop is worn or broken. What it does:

• Acts as a physical stop to limit door swing and prevent the door from swinging past its intended range
• Absorbs impact to reduce noisy or forceful door closing
• Helps maintain door alignment so the gasket seals properly
• Commonly replaces a worn, cracked, or missing stopper that causes the door to slam or hang unevenly

• One door stopper

• Disconnect power only if working near electrical components or wiring; otherwise remove items from the door and work on a stable surface
• Use basic hand tools; installation may require removing the door or partially loosening the hinge depending on model
• Inspect hinge and surrounding mounting area for wear or damage and replace any broken fasteners
• Tighten all fasteners securely and test door operation before returning the appliance to service

The Door Gasket is an OEM part for Frigidaire refrigerators. It is a thin, flexible strip of sealant material located around the perimeter of the refrigerator and freezer doors. The gasket provides a tight compression seal when the doors are closed in order to maintain optimal interior temperatures and energy efficiency.

Causes of a bad gasket can include hardening, cracking, or flattening of the material over many years of use and repeated door openings/closings.

Symptoms of a bad gasket include:

• Higher electricity bills from inadequate door sealing and cooling inefficiency
• Accumulation of frost or condensation around the door seal area
• Food inside spoiling more quickly due to temperature fluctuations

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This refrigerator door gasket provides a tight seal around the cabinet door to help keep cold air in and reduce moisture and frost buildup. Replacing a worn or torn gasket restores proper door sealing and helps maintain interior temperature. What it does:

• Seals the refrigerator door perimeter to reduce warm air infiltration — common symptoms: warm spots, condensation, or excessive frost.
• Keeps moisture out of the cabinet and door cavities to help prevent ice buildup and water pooling.
• Helps maintain more consistent internal temperatures for better food preservation.
• Restores proper door closure and can reduce cycling from frequent temperature loss.

• Unplug the appliance and remove food from the door before starting any replacement.
• Remove the old gasket and clean the gasket channel of debris before seating the new seal.
• Press the new gasket evenly into the retainer channel starting at the corners; avoid sharp tools or excessive force that can damage the seal.

This replacement closer helps the refrigerator door swing closed smoothly and hold the door in the correct position to improve seal and prevent gaps that let cold air escape. Replaces worn or damaged closers to restore proper door operation. What it does

• Guides and controls door movement so the door closes evenly and stays aligned.
• Helps the door latch and maintain a tight seal to reduce temperature loss.
• Eliminates sagging, uneven closing, or a door that drifts open.
• Works with the existing hinge and mounting hardware to restore factory operation.

• Basic hand tools required; remove power to the appliance and empty door contents before starting.
• Inspect hinge and mounting screws for wear or damage; replace damaged hardware as needed.
• Handle plastic components carefully to avoid cracking; tighten fasteners to secure but avoid over-torquing.

This replacement closer helps the refrigerator door swing closed smoothly and hold the door in the correct position to improve seal and prevent gaps that let cold air escape. Replaces worn or damaged closers to restore proper door operation. What it does

• Guides and controls door movement so the door closes evenly and stays aligned.
• Helps the door latch and maintain a tight seal to reduce temperature loss.
• Eliminates sagging, uneven closing, or a door that drifts open.
• Works with the existing hinge and mounting hardware to restore factory operation.

• Basic hand tools required; remove power to the appliance and empty door contents before starting.
• Inspect hinge and mounting screws for wear or damage; replace damaged hardware as needed.
• Handle plastic components carefully to avoid cracking; tighten fasteners to secure but avoid over-torquing.

This wire oven rack replaces a bent, rusted, or missing oven shelf to restore a stable cooking surface and smooth slide-in operation. It gives secure support for bakeware and helps maintain proper airflow for even cooking. What it does:

• Supports cookware and bakeware while baking, roasting, and broiling
• Slides into the oven's existing rack guides for stable positioning
• Restores lost clearance from warped or damaged racks so pans sit level
• Common symptoms: rack is bent, rusted, warped, or missing and cookware won't sit securely

• Allow the oven to cool completely and wear gloves to avoid sharp edges
• Slide the rack into the desired oven guide until fully seated; check both sides for proper alignment
• No special tools typically required; inspect oven guides for damage before reinstalling

This interior rack supports cookware or dishes at the correct level inside the appliance. Replace a bent, warped, rusted, or missing rack to restore safe, level support and proper operation.

• Provides a stable, level surface for loading and supporting items inside the unit
• Positions items at the intended height/clearance for proper performance
• Replace if bent/warped, corroded, or if the finish is flaking
• Common symptoms: rack wobbles or drops, items tip or slide, rust marks transfer

• Disconnect power before service; shut off gas or water. Allow the interior to cool completely
• Align the rack with the designated level and seat/slide into side supports or pegs per your model
• Inspect side supports/rails or clips and replace if worn or damaged
• Wear cut-resistant gloves—metal edges can be sharp