Parts for Frigidaire FFTR2045VB2: Doors Parts

This replacement name plate is the factory identification label that displays the appliance's model, serial and rating information so you can identify the unit and access accurate service or part information. It restores a legible, OEM-style data label for technicians and owners. What it does:

• Provides the appliance's model and serial number area used for parts lookup and service
• Shows electrical and capacity ratings
• Replaces a faded, damaged or missing identification label that prevents proper identification
• Helps ensure accurate ordering and diagnosis by restoring readable unit data

• One replacement name plate

• Mounting method varies by model; some name plates attach with adhesive, screws or rivets
• Clean surface and verify proper alignment before securing; use appropriate fasteners or adhesive for your model
• If rivets are used, rivet removal and installation may require specialty tools
• Disconnect power to the appliance before working in areas near electrical components

This gasket creates a tight seal between mating surfaces inside your appliance to prevent air or water leakage. Replacing a worn seal restores proper containment, helping the unit maintain performance, temperature control, and efficiency.

• Seals the joint between components to keep air and moisture from escaping or entering
• Helps the unit maintain stable temperatures and proper operation
• Replace if cracked, deformed, brittle, or no longer sealing
• Common symptoms: visible damage, leaks, condensation, or reduced performance due to poor sealing

• Disconnect power; shut off water supply if your repair involves any water connections
• Note the orientation of the original gasket before removal
• Clean and dry all mating surfaces; remove old adhesive or residue as needed
• After installation, run a quick test and check for leaks or gaps around the seal

This outer refrigerator door replaces a damaged or dented cabinet door to restore appearance and proper sealing. It provides the structural panel that mounts hinges, handles and the door gasket for normal operation and cooling performance. What it does:

• Replaces a damaged or dented outer refrigerator door panel
• Restores correct hinge alignment and door closing pressure
• Helps maintain proper internal temperature by supporting the gasket seal
• Prevents drafts, moisture intrusion and cosmetic blemishes

• Disconnect power and remove any food from door shelves before starting
• Door panels are heavy and may require two people to position and install
• Support the cabinet and follow OEM hinge/fastener order to avoid damage
• Check gasket condition and hinge fasteners after installation; adjust for proper seal

The Door Bin is an OEM part for Frigidaire refrigerators. It is designed to securely hold and organize products on the door, keeping them easily accessible and fresh.

A bad door bin can be caused by wear and tear, damage, or improper handling. When the assembly becomes faulty, it can result in issues such as a loose or broken door bin, difficulty in opening or closing the bin, or inadequate temperature control for items.

Symptoms of a bad bin include:

• Unstable or wobbly storage for dairy products
• Difficulty in accessing or retrieving items from the bin
• Spoiled items due to temperature fluctuations

Replace your faulty bin with this genuine OEM part to restore organization in your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The Door Bin is an OEM part for Frigidaire refrigerators. It is designed to securely hold and organize products on the door, keeping them easily accessible and fresh.

A bad door bin can be caused by wear and tear, damage, or improper handling. When the assembly becomes faulty, it can result in issues such as a loose or broken door bin, difficulty in opening or closing the bin, or inadequate temperature control for items.

Symptoms of a bad bin include:

• Unstable or wobbly storage for dairy products
• Difficulty in accessing or retrieving items from the bin
• Spoiled items due to temperature fluctuations

Replace your faulty bin with this genuine OEM part to restore organization in your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This bearing supports a rotating shaft within the appliance assembly, reducing friction for smooth, quiet operation. Replace a worn bearing to address grinding noise, wobble, or binding and to protect related components.

• Provides low-friction support for a rotating shaft or hub inside the assembly
• Helps maintain alignment for smooth, consistent rotation
• Reduces noise and wear from metal-on-metal contact
• Common failure signs: grinding/squealing, rough rotation, excess play/wobble, or intermittent binding

• Disconnect power; shut off water or gas before servicing
• Note orientation and any spacers/clips during disassembly to ensure correct reassembly
• Clean the shaft and housing; inspect mating parts and replace if worn or damaged
• Seat the bearing squarely using gentle, even pressure to avoid deforming the housing or shaft

This bearing supports and allows smooth rotation of the dryer drum, helping reduce noise and wear. Replacing a worn bearing restores stable drum movement and helps prevent scraping, thumping, or drag during cycles.

• Supports the rear of the drum for proper alignment and smooth rotation
• Can help address squeaking, grinding, scraping, or thumping sounds
• Reduce drum wobble, drag, or intermittent stopping during operation
• Wear item that can degrade over time with heat and load stress

• Disconnect power before service and allow components to cool
• Access typically requires removing the top and front panels
• Inspect the drum shaft, support bracket, and glides for wear; replace if needed
• Apply manufacturer-approved high-temp lubricant where specified

This replacement cover is an access panel that protects internal components and restores the appliance's appearance. It keeps wiring and controls enclosed for safer operation and a clean look. What it does:

• Protects internal components and wiring from dust, debris, and accidental contact
• Restores the exterior appearance where the original cover was damaged or missing
• Helps maintain proper airflow and clearance around covered components
• Reduces risk of accidental contact with moving or electrical parts

• Basic hand tools typically required; disconnect power before starting
• Handle carefully to avoid scratching painted surfaces
• Inspect mounting tabs or fasteners and replace any damaged hardware as needed
• Follow for removal and reassembly procedures

This auto-closer hook mounts at the door hinge and engages the closer/cam to help pull the door shut for a reliable seal. Replace a worn or broken hook to restore smooth, consistent self-closing action. What it does

• Couples the door to the hinge's auto-closer/cam mechanism
• Helps the door finish closing and stay closed
• Reduces bounce-back so the gasket can seal properly
• Common symptoms: door won't self-close, pops back open, feels loose at the lower hinge, or the original hook is cracked/worn

• 1 auto-closer hook

• Disconnect power before servicing; support the door and use a helper if removing it from the hinge
• Access the lower hinge/closer area; remove the damaged hook and transfer any spacers or screws
• Install the new hook in the same orientation; tighten hardware securely
• Recheck door alignment and inspect the mating cam/closer if issues persist

The Hook is an OEM part for Frigidaire refrigerators. It helps to ensure a secure and proper closure of the refrigerator door.

A bad door closer hook can be caused by wear and tear, damage, or misalignment. Signs of a faulty door closer hook include the door not closing fully or not staying closed, difficulty in opening or closing the door smoothly, or a loose or wobbly door.

Symptoms of a bad door closer hook can include:

• The refrigerator door not sealing properly
• Excessive force required to open or close the door
• Visible damage or misalignment of the door closer hook

Replace your worn or damaged door closer hook with this genuine OEM part to restore your refrigerator door. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This factory screw secures interior or door components in your refrigerator so they stay tight and aligned. Replace missing, stripped, or corroded hardware to eliminate looseness and prevent parts from shifting or rattling during use.

• Fastens brackets, trim, rails, bins, or handles to the cabinet or door
• Restores a secure fit when the original screw is lost, damaged, or rusted
• Helps correct looseness, vibration, and rattling from unsecured parts
• Common symptoms: loose or wobbling handle/trim, misaligned parts, missing hardware

• Disconnect power to the appliance before servicing; turn off water if working near dispenser/ice areas
• Match to the original hardware and install in the same location; reuse any washers/spacers
• Start threads by hand to prevent cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to avoid stripping threads or cracking plastic