Parts for Frigidaire FGTR2037TD4: Doors Parts

This freezer door gasket creates an airtight seal between the door and cabinet to keep cold air in and moisture out. Replacing a worn gasket helps restore proper temperatures, reduce frost and condensation, and improve efficiency.

• Seals the freezer door perimeter to prevent warm-air leaks and temperature swings
• Helps reduce frost buildup and condensation around the door opening
• Can resolve issues like visible gaps, a torn or deformed gasket, or a door that won't seal
• Supports consistent cooling performance and reduces excessive run time

• Disconnect power to the refrigerator before servicing
• Let the new gasket relax at room temperature; use warm water or low heat to smooth folds
• Clean the door sealing surface thoroughly; install the gasket evenly, ensuring corners are fully seated
• Close the door and check for uniform contact all around; gently massage high spots and re-seat as needed

The Refrigerator Door Gasket is an OEM replacement part for Frigidaire refrigerators. As a sealing component, it surrounds the door frame to keep cold air circulating optimally. Proper installation and fit maintains energy efficiency.

Causes of failure involve cracks arising over constant compression and expansion during repeated openings. Mineral buildup may also compromise the seal over time.

Symptoms of a defective gasket include:

• Cooler air detectable escaping around door edges
• Condensation visible on door seal
• Temperature fluctuations noticed inside refrigerator

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore ranges.

The Dairy Door is an OEM replacement part for  Frigidaire side-by-side refrigerators. Located inside the fresh food compartment, it provides a dedicated storage area for milk, yogurt, cheese and other dairy products requiring colder temperatures. The door measures approximately 9 inches wide and 5 inches high.

Causes of a bad dairy door include normal wear from repeated opening and closing over time. Exposure to spills inside the refrigerator can also potentially damage door shelf components or seals.

Symptoms of a bad dairy door are: 

• Difficulty opening or closing the door smoothly  
• Door alignment issues where it does not sit flush in the frame
• Leaks or moisture inside the dairy storage area
• Damage or cracks in shelf supports or gasket seals

This OEM part is also compatible with models from brands like Electrolux, Gibson, and Kelvinator brand models.

NOTE: For white use 240337701

This small black plug/button covers a hinge or bearing access hole to restore a finished appearance and help keep out dirt and debris. It's a simple, inexpensive trim piece that maintains the appliance's look and helps protect internal components. What it does:

• Covers exposed hinge or bearing access holes for a clean, finished appearance
• Helps keep dust and debris out of hinge or bearing cavities
• Prevents snagging and reduces the chance of small items entering the opening
• Matches factory appearance and fit for a seamless repair

• Push-fit design; press into the hole until fully seated
• Keep away from small children — small part is a choking hazard

This door stop limits the opening range of your refrigerator door to prevent overextension and hinge strain. Replace a worn or broken stop to restore controlled door movement and protect surrounding cabinetry from accidental impacts. What it does:

• Controls how far the door opens to prevent overextension and damage
• Helps maintain proper door alignment and reduces stress on the hinges
• Replaces cracked, deformed, or missing stops that no longer hold the door at its stop point
• Common symptoms include the door swinging too far, a hard "clunk" at full open, or visible damage to the stop

• 1 door stop

• Disconnect power; turn off water supply if your unit has a dispenser/ice maker
• Support the door before loosening any hinge fasteners to access the stop
• Note the stop's orientation and position; transfer any spacers and reinstall the same way
• Open and close the door to verify proper range and clearance before fully tightening fasteners

The Door Stop is an OEM part for Frigidaire refrigerators. This small part helps protect the appliance's door from damage and prevents it from impacting walls or adjacent cabinetry, ensuring the longevity and integrity of your refrigerator's exterior. 

Causes of a bad Door Stop can range from physical damage due to forceful door opening, to normal wear and tear from repeated use. In some cases, the mounting area for the door stop may become worn or damaged, affecting its ability to hold the door stop securely.

Symptoms of a bad Door Stop include:

• The refrigerator door swings open wider than usual
• Noticeable wear, damage, or breakage on the door stop
• Difficulty in opening or closing the door smoothly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

A small black replacement plug button that restores a clean, finished appearance and helps keep controls and openings free from dirt and moisture. Designed as a direct-fit cosmetic and protective cap for compatible appliance openings. What it does

• Covers exposed holes or button openings to prevent debris and spills from entering internal areas
• Restores the original look where a worn or missing plug detracts from the appliance finish
• Holds in place to protect underlying components from accidental contact
• Useful when replacing control bezels or trim that require a matching push-in cap

• Disconnect power to the appliance before performing any service work
• Press the plug button squarely into the opening until it snaps into place; no special tools typically required
• Inspect the mounting hole for damage or debris before installing to ensure a secure fit
• If the part does not seat properly, do not force it; verify correct part and orientation

This replacement mounting screw secures components and panels in refrigerators and freezers, restoring proper fit and stopping loose or rattling parts. Use when original screws are missing, stripped, or damaged. What it does:

• Fastens trim, panels, brackets or small components to the appliance frame
• Restores secure attachment to stop rattling or intermittent contact
• Replaces stripped, corroded, or missing screws to prevent parts from shifting
• Simple, direct replacement that matches the original mounting point

• Use the matching driver bit to avoid stripping the screw head
• Tighten until snug; do not overtighten to prevent thread damage
• Disconnect power to affected appliance areas before servicing if panels expose wiring
• If threads are damaged, replace the mating nut or tapped insert as needed

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Hinge Bearing is an OEM part for Frigidaire refrigerators. It is designed to facilitate the smooth opening and closing of the refrigerator door by providing a pivot point for the door hinge. This bearing ensures that the door moves easily and remains properly aligned, helping to maintain a tight seal and optimal refrigerator performance.

Causes of a bad hinge bearing can include regular wear and tear from frequent use, exposure to moisture or temperature changes, and physical damage due to accidental impacts. Over time, these factors can cause the hinge bearing to wear out, become loose, or break, affecting the door's functionality.

Symptoms of a bad hinge bearing include:

• Difficulty opening or closing the refrigerator door
• The door not staying in place or sagging
• Unusual noises, such as squeaking or grinding, when the door is moved
• The door not sealing properly, leading to temperature fluctuations inside the refrigerator

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Shelf Bin is an OEM replacement part for Frigidaire refrigerators. It is designed to fit on the refrigerator door, providing convenient storage space for condiments, bottles, and other small items. This shelf bin helps to keep the refrigerator organized, making it easier to find and reach items stored in the door. 

Causes of a bad door shelf bin can include cracking, breaking, or warping due to overloading, impact from items being moved in and out, or deterioration over time.

Symptoms of a bad door shelf bin include:

• Cracks or breakage in the bin.
• The bin not securely attaching to the door.
• Items falling out or not fitting properly in the bin.
• Difficulty in accessing or retrieving items from the bin.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Refrigerator Door Shelf is an OEM replacement part for Frigidaire refrigerators, designed to offer convenient storage space for jars, bottles, and other condiments within easy reach. Measures approximately 24 1/2 inches wide X 2 1/2 inches deep

Causes of a bad Refrigerator Door Shelf can include physical damage such as cracks or breaks from overloading it with too heavy items. Additionally, wear and tear over time can lead to the shelf becoming damaged.  

Symptoms of a bad Refrigerator Door Shelf include:

• Visible cracks or damage
• The shelf sagging or unable to retain items  
• Difficulty fitting the shelf into its designated slots  

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Refrigerator Door Shelf is an OEM replacement part for Frigidaire refrigerators, designed to offer additional storage space within the door of the appliance. This part provides a space for organizing items such as condiments, jars, and bottles, making them easily accessible while maximizing the interior storage of the refrigerator. Measures approximately 24 ¼ inches by 3 ¾  inches

Over time, the shelf can crack or break due to frequent use, overloading, or accidental impacts. A compromised door shelf can lead to instability and difficulty in securely holding items.

Symptoms of a bad Refrigerator Door Shelf include:

• Cracks or visible damage to the shelf
• Difficulty attaching the shelf to the door
• Items falling out or not staying in place
• Reduced storage capacity on the door

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Freezer Door Shelf Bin is an OEM replacement part for Frigidaire refrigerators. It provides adjustable storage on the inside of the freezer door with removable bin shelves. These bins maximize storage potential in the limited door space through customizable shelving.

Causes of a bad Door Shelf Bin can include shelf breakage from heavy loads, damage to supporting rails or walls of the bin inhibiting proper shelf attachment and use, or broken/missing bin walls reducing structural integrity.

Symptoms of a bad Door Shelf Bin include:

• Detached or missing shelves
• Shelves that do not stay firmly in place when loaded
• Damage or deterioration of bin walls
• Insufficient or compromised storage space

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

This part number contains one (1) screw.

The Door Handle Screw is an OEM part for Frigidaire refrigerators. This screw secures the door handle to the refrigerator door, ensuring a firm and stable grip for opening and closing the door.

Causes of a bad door handle screw can include regular wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or stripping. A faulty screw can lead to a loose or wobbly door handle, making it difficult to operate the refrigerator.

Symptoms of a bad door handle screw include:

• The door handle feeling loose or coming off
• Difficulty in securely tightening the handle
• Visible rust or corrosion on the screw
• Stripped threads on the screw or handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is a service wrench used to loosen and tighten appliance fasteners for maintenance and repairs, making access and part replacement easier for technicians and DIYers. Durable tool designed for specific appliance fastener sizes. What it does:

• Provides the correct fit and leverage for removing or installing designated appliance nuts, bolts, and fittings
• Helps safely access internal components during service and part replacement
• Reduces risk of rounding fasteners compared with improvised tools
• Useful for routine maintenance tasks and repair procedures that require a dedicated wrench

• One wrench

• Use the wrench only for its intended appliance fasteners; avoid excessive force
• Disconnect power and water to the appliance before beginning service
• Wear safety gloves and eye protection when working on appliances