Parts for Frigidaire FRT21INGJB0: 02 - Doors Parts

Color: white. Measures about 1-1/2 inches high by 1 inch deep.

Color: white. Measures about 1-1/2 inches high by 1 inch deep.

Cut to fit design.

This part has been discontinued and is no longer available.

A small black replacement plug button that restores a clean, finished appearance and helps keep controls and openings free from dirt and moisture. Designed as a direct-fit cosmetic and protective cap for compatible appliance openings. What it does

• Covers exposed holes or button openings to prevent debris and spills from entering internal areas
• Restores the original look where a worn or missing plug detracts from the appliance finish
• Holds in place to protect underlying components from accidental contact
• Useful when replacing control bezels or trim that require a matching push-in cap

• Disconnect power to the appliance before performing any service work
• Press the plug button squarely into the opening until it snaps into place; no special tools typically required
• Inspect the mounting hole for damage or debris before installing to ensure a secure fit
• If the part does not seat properly, do not force it; verify correct part and orientation

Replace a cracked or broken handle with this black refrigerator door handle. It restores a solid, comfortable grip so you can open and close the door normally and keep your appliance looking clean and intact.

• Restores a secure handhold for opening and closing the door
• Common fix for cracked, broken, or missing door handles
• Helps address a wobbly handle when the handle's mounting points are damaged
• Refreshes the appliance's appearance with a matching black finish

• Disconnect power to the appliance before servicing
• Remove any decorative screw covers if present, then support the handle while removing mounting screws
• Align the new handle with existing mounting holes and tighten screws evenly—do not overtighten
• Check that the handle is secure and the door opens and closes normally

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Stick on

Snap in

This replacement door bin restores a refrigerator door's interior storage for bottles, jars and small items. It provides a secure, easy-to-clean shelf that helps keep contents organized and accessible. What it does:

• Replaces a cracked, broken or worn refrigerator door storage bin
• Holds bottles, condiments and small containers securely on the door
• Restores proper fit and prevents items from falling during normal use
• Clear plastic lets you see contents at a glance

• One door bin

• Removes and installs by snapping into existing door-mounted support rails; no tools typically required
• Handle parts gently to avoid cracking; plastic can be brittle if cold
• Clean with mild soap and water; avoid abrasive cleaners or high-heat drying
• If the bin does not seat fully, check door support rails are undamaged before forcing

This factory screw fastens refrigerator components and panels. It replaces missing or damaged hardware so parts stay aligned and secure, reducing looseness and rattles caused by vibration. What it does:

• Secures panels, brackets, and trim per your model's design
• Helps maintain alignment and reduce vibration-related loosening or noise
• Replaces missing, stripped, or corroded hardware
• Restores a snug fit when threads or heads are worn

• One screw

• Disconnect power; turn off the water supply if working near ice or dispenser systems
• Use the correct driver; start threading by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking adjacent plastic
• Refer to your model's diagram to confirm location and quantity used

Size: Approximate 2.5 inches thick, 33 inches wide and 70 inches long.