Parts for Frigidaire FRT21P6BSB2: 03 - Doors Parts

This freezer door gasket creates an airtight seal between the door and cabinet to keep cold air in and moisture out. Replacing a worn gasket helps restore proper temperatures, reduce frost and condensation, and improve efficiency.

• Seals the freezer door perimeter to prevent warm-air leaks and temperature swings
• Helps reduce frost buildup and condensation around the door opening
• Can resolve issues like visible gaps, a torn or deformed gasket, or a door that won't seal
• Supports consistent cooling performance and reduces excessive run time

• Disconnect power to the refrigerator before servicing
• Let the new gasket relax at room temperature; use warm water or low heat to smooth folds
• Clean the door sealing surface thoroughly; install the gasket evenly, ensuring corners are fully seated
• Close the door and check for uniform contact all around; gently massage high spots and re-seat as needed

The Refrigerator Door Gasket is an OEM part for Frigidaire refrigerators. It lines the edge of the refrigerator door, creating an airtight seal that prevents warm air from entering and cold air from escaping the unit. This seal is crucial for maintaining the efficiency of the refrigerator, ensuring that it runs smoothly and keeps food at the correct temperatures without overworking the cooling system.

Symptoms of a bad Refrigerator Door Gasket include:

• Visible cracks, splits, or wear in the gasket material
• Condensation or frost build-up around the door edges
• The refrigerator door not closing fully or seeming to have air leaks

Causes of a bad door gasket can stem from natural degradation over time, exposure to food oils and residues that degrade the rubber, or deformities caused by improper door usage or accidents.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Rack is an OEM part for Frigidaire refrigerators. This component provides additional storage on the refrigerator door, allowing for convenient organization of bottles, jars, and other small items. This white door bar measures approximately 20.27 inches.

Causes of a bad door rack can include cracking or breaking due to heavy items being stored on it, wear and tear from frequent use, or damage from impacts or mishandling. Exposure to extreme temperature changes can also weaken the plastic over time.

Symptoms of a bad door rack include:

• The rack falling off or not staying securely in place
• Visible cracks or damage to the rack
• Difficulty in attaching the rack to the door
• Items not being held securely and falling out when the door is opened

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Rack Support is an OEM part for Frigidaire refrigerators. It is designed to support the door rack or bin, providing a secure mounting point that helps hold items in place within the refrigerator door. This support piece ensures that the door racks remain stable, allowing you to store and organize items like bottles, jars, and condiments efficiently.

Causes of a bad door rack support can include regular wear and tear from frequent use, overloading the door racks with heavy items, or accidental damage from impacts or mishandling. Over time, these factors can cause the support to crack, break, or lose its ability to hold the door rack securely.

Symptoms of a bad door rack support include:

• Door racks sagging or falling out of place
• Difficulty in fitting or securing the door racks
• Visible cracks, breaks, or damage to the support

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Refrigerator Door Rack Support is an OEM replacement part for Frigidaire refrigerators. This component provides structural reinforcement and stability for the racks or shelves mounted on the interior of the refrigerator door.

Symptoms of needing to replace the door rack support include:

• Sagging or unstable door racks
• Difficulty in removing or inserting the racks
• Visible cracks, damage, or deformation of the support

Causes of a faulty door rack support can include accidental impact or mishandling, excessive weight or stress on the racks, or general wear and tear over time.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models.

The Door Rack Support is an OEM replacement part for Frigidaire refrigerators. It serves as the mounting bracket or structure that holds and secures the door racks or bins in place on the inside of the refrigerator door.

Symptoms of a need to replace the door rack support:

• Loose or wobbly door racks or bins
• Racks or bins falling off the door when opened
• Visible cracks, breaks, or damage to the support structure

Causes of a faulty door rack support can include general wear and tear over time, physical impact or mishandling, or manufacturing defects in the material or construction.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models.

The Refrigerator Door Rack Support is an OEM replacement part for Frigidaire refrigerators. It is a crucial component that provides structural support and stability for the door racks or bins, ensuring they remain securely in place even when loaded with items.

Symptoms of a bad refrigerator door rack support include:

• Door racks or bins becoming loose or unstable
• Racks or bins not aligning properly when the door is closed
• Items falling off the racks due to lack of support

Causes of a bad door rack support can range from physical damage due to impact or excessive force to general wear and tear over time, which can weaken or deform the support.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

For the right-hand side order 240311502.

The Dairy Door is an OEM replacement part for  Frigidaire side-by-side refrigerators. Located inside the fresh food compartment, it provides a dedicated storage area for milk, yogurt, cheese and other dairy products requiring colder temperatures. The door measures approximately 9 inches wide and 5 inches high.

Causes of a bad dairy door include normal wear from repeated opening and closing over time. Exposure to spills inside the refrigerator can also potentially damage door shelf components or seals.

Symptoms of a bad dairy door are: 

• Difficulty opening or closing the door smoothly  
• Door alignment issues where it does not sit flush in the frame
• Leaks or moisture inside the dairy storage area
• Damage or cracks in shelf supports or gasket seals

This OEM part is also compatible with models from brands like Electrolux, Gibson, and Kelvinator brand models.

NOTE: For white use 240337701

The Door Rack is an OEM part for Frigidaire refrigerators. This component provides additional storage on the refrigerator door, allowing for convenient organization of bottles, jars, and other small items. This white door bar measures approximately 20.27 inches.

Causes of a bad door rack can include cracking or breaking due to heavy items being stored on it, wear and tear from frequent use, or damage from impacts or mishandling. Exposure to extreme temperature changes can also weaken the plastic over time.

Symptoms of a bad door rack include:

• The rack falling off or not staying securely in place
• Visible cracks or damage to the rack
• Difficulty in attaching the rack to the door
• Items not being held securely and falling out when the door is opened

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Stop is an OEM part for Frigidaire refrigerators. This small part helps protect the appliance's door from damage and prevents it from impacting walls or adjacent cabinetry, ensuring the longevity and integrity of your refrigerator's exterior. 

Causes of a bad Door Stop can range from physical damage due to forceful door opening, to normal wear and tear from repeated use. In some cases, the mounting area for the door stop may become worn or damaged, affecting its ability to hold the door stop securely.

Symptoms of a bad Door Stop include:

• The refrigerator door swings open wider than usual
• Noticeable wear, damage, or breakage on the door stop
• Difficulty in opening or closing the door smoothly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Hinge Bearing is an OEM part for Frigidaire refrigerators. It is designed to facilitate the smooth opening and closing of the refrigerator door by providing a pivot point for the door hinge. This bearing ensures that the door moves easily and remains properly aligned, helping to maintain a tight seal and optimal refrigerator performance.

Causes of a bad hinge bearing can include regular wear and tear from frequent use, exposure to moisture or temperature changes, and physical damage due to accidental impacts. Over time, these factors can cause the hinge bearing to wear out, become loose, or break, affecting the door's functionality.

Symptoms of a bad hinge bearing include:

• Difficulty opening or closing the refrigerator door
• The door not staying in place or sagging
• Unusual noises, such as squeaking or grinding, when the door is moved
• The door not sealing properly, leading to temperature fluctuations inside the refrigerator

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Screw Kit is an OEM part for Frigidaire appliances. It contains various screws specifically designed to fit and secure different components of Frigidaire appliances, ensuring a tight and secure assembly. This kit is essential for both initial installations and for making repairs or replacements to existing appliances, providing the necessary hardware to maintain or restore the structural integrity of your appliance.  These screws are #10-16 x .500 inches long and can be loosened or tightened using either a Phillips-head or square-head screwdriver.

Symptoms of needing a new Screw Kit include:

• Loose components or panels on your appliance due to missing or damaged screws.
• Inability to securely fasten parts during assembly or repairs, which can lead to operational issues or safety hazards.
• Screws stripping or corroding over time, which can compromise the stability and durability of the appliance.

Causes for replacing screws can include mechanical stress that causes screws to loosen or fall out, environmental factors like moisture leading to corrosion, or accidental damage during cleaning or maintenance.

This screw kit is designed to be universally compatible with various Frigidaire models, ensuring that you have the right screws for a range of repair needs.