Parts for Ge GTE19JSNBRSS: Doors Parts

The Stainless Steel Handle Set is an OEM replacement part for GE refrigerators. This comprehensive set includes both the refrigerator and freezer door handles, along with the necessary mounting hardware for a complete installation.

Symptoms of a bad Stainless Steel Handle Set include:

• Handles becoming loose or detached
• Difficulty in opening the refrigerator or freezer doors
• Visible wear, tarnish, or damage to the handles affects aesthetics and grip

Causes for a malfunctioning Stainless Steel Handle Set can include wear and tear from frequent use, mechanical issues with the attachment points, or environmental factors that affect the material's integrity.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This freezer door gasket seals the freezer door to help maintain proper temperature and reduce frost buildup. Replacing a worn or torn gasket restores the door seal for more consistent cooling and energy use. What it does:

• Creates an airtight seal around the freezer door to help keep cold air in and warm, moist air out
• Stops or reduces frost accumulation and condensation caused by a failing seal
• Helps the freezer maintain set temperature more reliably and can reduce compressor cycling
• Use when the existing gasket is torn, warped, compressed, or no longer seals evenly

• Disconnect power to the appliance before beginning any work and follow the manufacturer's safety recommendations
• Remove the old gasket, clean the gasket channel thoroughly, then align the new gasket starting from one corner and press it into the channel
• If gasket is stiff, warm it slightly (hand-warm or a hair dryer on low) to make installation easier—avoid overheating
• After installation, check the door seal around the entire perimeter and adjust or reseat as needed for an even contact

This freezer door stop replaces the damaged or worn bumper that cushions the freezer door, helping it close smoothly and preventing damage to the door or cabinet. Color-matched Dorian Gray finish. What it does:

• Cushions door movement to reduce banging and wear
• Helps the door seal more consistently by providing proper stopping position
• Reduces noise when opening or closing the freezer door
• Restores original fit and finish for a clean, finished appearance

• Basic hand tools may be required; follow the appliance manufacturer's instructions
• Power off and empty the door area if required for safe access before installing
• Inspect surrounding trim and mounting area; replace mounting screws if worn or damaged

This replacement refrigerator door stop cushions and limits door travel to help prevent slamming and misalignment. It restores smooth, controlled door movement and helps the door stay properly positioned for reliable sealing. What it does:

• Absorbs impact and reduces door slam noise when opening or closing
• Limits door travel to prevent over-rotation that can damage the cabinet or hinge
• Helps maintain proper door alignment for an effective seal
• Commonly used when a door slams, hangs open, or rubs against the cabinet

• Unplug the appliance or disconnect power before working near electrical components
• Support the door while removing or installing the stop to prevent it from shifting
• Use appropriate hand tools; do not force or overtighten fasteners

This fresh food door gasket seals the refrigerator compartment to keep cold air in and warm air out. The Dorian Gray color matches compatible units while helping maintain stable temperatures and reducing moisture at the door edge. What it does:

• Creates an airtight seal around the fresh food door to prevent air leaks
• Helps maintain proper compartment temperature and humidity
• Reduces condensation, frost, and warm spots near the door opening
• Common failure signs: gaps, cracks/tears, warped corners, or the door not closing/sealing properly

• 1 fresh food door gasket in Dorian Gray

• Disconnect power before servicing; clear items from the door for easier handling
• Warm the new gasket (soak in warm water or use a hair dryer on low) to relax and improve fit
• Press the gasket fully into the door channel; ensure corners seat evenly without twists
• After installation, close the door to help the gasket conform; check for an even seal and adjust door alignment if needed

This reversible door plug is a small trim cap that fills the unused holes on a refrigerator door after changing the door swing. It restores a clean, finished look and helps keep dust and moisture out.

• Covers unused hinge/handle screw holes created during a door reversal
• Press-fit cap designed to match lighter gray door trim
• Helps maintain appearance and reduce entry of dirt and moisture
• Replace if missing, cracked, discolored, or won't stay seated

• Disconnect power if removing or repositioning the door/hinges
• Use your model's parts diagram to confirm the plug location and color
• Align with the hole and press in by hand until flush with the surface
• Do not force; verify correct part if the plug will not seat properly

The Handle Mount is an OEM component specifically designed for GE French door refrigerators. It serves as the attachment point for refrigerator door handles.

The handle mount connects the handle assembly securely to the refrigerator door itself. Its sturdy construction manages stress from frequent usage while allowing for smooth operation.

Symptoms of a bad handle mount include:

• Loose, unstable, or detached door handles
• Handles difficult-to-operate or open doors with  
• Visible bending, cracks, or damage to the mount
• Reduced grip strength or door control

Causes can involve normal wear over extended periods, imprecise impacts, or repeated stress from heavy handling exceeding the mount’s limits. 

Replace with this genuine GE OEM part to restore a tight, lasting connection between handles and doors. Compatible also with Hotpoint, RCA, and Kenmore French door refrigerator models.
 

A small plastic thimble that fits behind a push-style control button to hold it squarely in the housing and restore smooth button travel. Replaces a worn or missing retainer to improve button feel and alignment. What it does:

• Secures push-style control buttons in the panel to stop wobble or uneven movement
• Restores proper button travel so controls depress and release cleanly
• Helps keep the button centered in its bezel for consistent operation
• Addresses symptoms like buttons that fall out, sit crooked, or don't return smoothly

• Disconnect power to the appliance before beginning any repair
• Remove the knob or access the control panel per your model's service instructions
• Press the thimble into the button housing until it snaps or seats fully; then reinstall the button/knob

The Screw is an OEM replacement part for GE brand refrigerators. It is commonly used to secure panels, handles, shelves, or other parts of the refrigerator.

Causes of a faulty refrigerator screw can include wear and tear over time, damage due to mishandling or over-tightening, or loss of thread integrity. These factors can result in loose or ineffective connections, compromising the stability or functionality of the attached components.

Symptoms of a bad refrigerator screw may include:

• Loose or wobbly panels, handles, or shelves
• Difficulty in attaching or securing components
• Visible damage or breakage of the screw

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.